Stainless Steel 1.4818
EN 1.4818
1.4818 (X6CrNiSiNCe19-10) is a silicon-, nitrogen- and cerium-modified 18-10 austenitic stainless developed for better oxidation and scaling resistance at elevated temperature than standard 304.
Reference datasheet — 1.4818 is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the Annealed condition
1.4818 tempers and conditions
1.4818 is supplied in 3 conditions, soft to hard. Annealed is the default FabDigit quotes; the values on this page are for it.
Compare all 3 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
AnnealedDefault Solution Annealed (1050–1100 °C, rapid cool) | Standard supply condition for all product forms — maximum ductility, fully austenitic, best oxidation and corrosion performance. | 330 | 650 | 45 | 180 HB | — |
As-welded deposit | Fabricated condition for furnace weldments; weld metal strength matches base metal but hot ductility and oxidation life are slightly lower than annealed parent. | 340 | 620 | 35 | 195 HB | 2 % IACS |
Cold drawn | Choose for tight tolerance, higher room-temperature strength and better chip control; strength gain is lost above ~600 °C by recovery. | 520 | 780 | 25 | 22 HRC | 2 % IACS |
Supply forms, finishes and certifications
Ways 1.4818 is supplied — form, process route, surface or paperwork — without a datasheet of their own. The property values above apply.
| Option | What it is | Type |
|---|---|---|
HR-Bar-Ann | Hot rolled bar, solution annealed and pickled | Supply form |
Tube-Ann | Seamless / welded tube, solution annealed | Supply form |
1D | Hot rolled plate/sheet, heat treated and pickled | Surface finish |
2B | Cold rolled, annealed, pickled, skin passed | Surface finish |
2R | Bright annealed cold rolled | Surface finish |
What is 1.4818?
1.4818 (X6CrNiSiNCe19-10) is a silicon-, nitrogen- and cerium-modified 18-10 austenitic stainless developed for better oxidation and scaling resistance at elevated temperature than standard 304. It is available as hot- and cold-rolled sheet (1D, 2B, 2R), annealed and cold-drawn bar, annealed and as-welded tube, with 330 MPa yield, 650 MPa tensile, 45 % elongation and 180 HB (88 HRB) and a 1050 °C maximum service temperature. Silicon and nitrogen make it tougher and more work-hardening than 304, so formability is rated 72 and cutting speeds are lower; for still higher temperatures step up to a 21Cr-11Ni (1.4835-type) grade. 1.4818 has a density of 7.7 g/cm³ (0.278 lb/in³), lighter than 83% of stainless steel grades. It melts at 1,400°C (2,552 °F). 1.4818 has a yield strength of 330 MPa (47.9 ksi) and a tensile strength of 650 MPa (94.3 ksi) — weaker than 57% of stainless steel grades. Elongation at break is 45% and the elastic modulus is 200 GPa (29 Msi).
What is 1.4818 used for?
- furnace fittings
- exhaust components
- heat-treatment fixtures
Advantages
- High service temperature — 1,050°C (1,922 °F), better than 91% of stainless steel grades
- Tough — resists crack growth — 200 MPa·√m (182 ksi·√in), better than 86% of stainless steel grades
- Forms and bends easily — 72/100, better than 84% of stainless steel grades
- Readily welded — 80/100, better than 80% of stainless steel grades
- Ductile — tolerates forming and impact — 45%, better than 76% of stainless steel grades
Limitations
- Low electrical conductivity — 2 % IACS, worse than 77% of stainless steel grades
- High embodied carbon — 5.5 kg CO₂/kg, worse than 77% of stainless steel grades
1.4818 properties
Typical room-temperature values for 1.4818-Annealed; bars are the position among stainless steel grades.
Physical3
1.4818 has a density of 7.7 g/cm³ (0.278 lb/in³), lighter than 83% of stainless steel grades. It melts at 1,400°C (2,552 °F).
Mechanical15
1.4818 has a yield strength of 330 MPa (47.9 ksi) and a tensile strength of 650 MPa (94.3 ksi) — weaker than 57% of stainless steel grades. Elongation at break is 45% and the elastic modulus is 200 GPa (29 Msi).
Thermal6
1.4818 is rated for continuous service to 1,050°C (1,922 °F). It conducts heat at 15 W/m·K (8.67 BTU/hr·ft·°F), worse than 59% of stainless steel grades. Thermal expansion is 16.5 µm/m·K (9.17 µin/in·°F).
Electrical3
1.4818 conducts electricity at 2 % IACS, worse than 77% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is good (68/100), better than 63% of stainless steel grades.
Sustainability4
Producing a kilogram of 1.4818 takes about 55 MJ of energy and emits 5.5 kg of CO₂ — more than 50% of stainless steel grades. Typical recycled content is 60%.
Manufacturability7
1.4818's machinability is poor (33/100, worse than 57% of stainless steel grades); weldability very good (80/100); formability very good (72/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the stainless steel family
Yield strength against density for every stainless steel grade FabDigit runs. 1.4818 is highlighted; hover a dot for its name, or open the interactive family chart.
Working with 1.4818
Is 1.4818 easy to machine?
Machines like 304 but tougher and more gummy from Si+N — use rigid setups, positive-rake coated carbide, 60–100 m/min, heavy feed to cut under the work-hardened layer and flood coolant.
Can 1.4818 be welded?
Excellent weldability by GTAW/GMAW/SMAW without pre- or post-weld heat treatment; use matching, 22-12H or 253 MA type fillers, keep interpass below ~150 °C and heat input moderate to limit ferrite/σ issues.
Can 1.4818 be formed, bent or molded?
Cold forms and deep draws well but work-hardens faster than 304 — allow extra springback and interstage annealing at 1050–1100 °C; hot work at 1150–900 °C with rapid cooling.
1.4818 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| C | 0.04 – 0.08 | 0.05 |
| Sikey oxidation-scale former | 1 – 2 | 1.4 |
| Mn | ≤ 0.8 | 0.6 |
| P | ≤ 0.05 | 0.03 |
| S | ≤ 0.02 | 0 |
| Cr | 18 – 19 | 18.5 |
| Ni | 9 – 11 | 9.5 |
| Nsolid-solution strengthening | 0.12 – 0.2 | 0.15 |
| Cerare-earth addition improving oxide-scale adhesion | 0.03 – 0.08 | 0.05 |
| Fe | balance |
What surface finishes work on 1.4818?
Pickle/passivate after hot work or welding to restore the Si-Cr oxide; no anodising — electropolishing or mechanical polishing for surface quality, and avoid carbon-steel contamination on grinding media.
Surface treatments FabDigit runs on stainless steel parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Passivation
Organic Coating
Thermal Spray
Equivalent designations
Standards and trade names that resolve to Stainless Steel 1.4818 in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- EN / DIN / Werkstoff-Nr.
- X6CrNiSiNCe19-10
How much does 1.4818 cost?
1.4818 is a premium-cost stainless steel ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
1.4818 — frequently asked
What is 1.4818 used for?
1.4818 is typically used for furnace fittings, exhaust components and heat-treatment fixtures. In short: oxidation-resistant 18-10; service to 1050 °C; welds without heat treatment.
What is the yield strength of 1.4818?
1.4818 has a typical yield strength of 330 MPa (47.9 ksi) and a tensile strength of 650 MPa (94.3 ksi) — weaker than 57% of stainless steel grades. Strength varies by condition: see the 3 listed tempers.
Is 1.4818 easy to machine?
Not especially — machinability is rated poor (33/100, worse than 57% of stainless steel grades). Machines like 304 but tougher and more gummy from Si+N — use rigid setups, positive-rake coated carbide, 60–100 m/min, heavy feed to cut under the work-hardened layer and flood coolant.
Can 1.4818 be welded?
Yes — weldability is rated very good (80/100). Excellent weldability by GTAW/GMAW/SMAW without pre- or post-weld heat treatment; use matching, 22-12H or 253 MA type fillers, keep interpass below ~150 °C and heat input moderate to limit ferrite/σ issues.
What surface finishes work on 1.4818?
Pickle/passivate after hot work or welding to restore the Si-Cr oxide; no anodising — electropolishing or mechanical polishing for surface quality, and avoid carbon-steel contamination on grinding media.
Can 1.4818 be formed, bent or molded?
Cold forms and deep draws well but work-hardens faster than 304 — allow extra springback and interstage annealing at 1050–1100 °C; hot work at 1150–900 °C with rapid cooling.
What is the maximum service temperature of 1.4818?
1.4818 is rated for continuous use to about 1,050°C (1,922 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between 1.4818 Annealed and 1.4818-CD?
Annealed is the default condition — standard supply condition for all product forms — maximum ductility, fully austenitic, best oxidation and corrosion performance. CD: choose for tight tolerance, higher room-temperature strength and better chip control; strength gain is lost above ~600 °C by recovery. Yield strength is 330 MPa in Annealed versus 520 MPa in CD.
How much does 1.4818 cost?
1.4818 is a premium-cost stainless steel ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- EN 10095 — Heat resisting steels and nickel alloys — CEN (2018)
- EN 10088-1/-2 — Stainless steels: list of grades, sheet/plate technical delivery conditions — CEN (2014)
- Outokumpu 153 MA (EN 1.4818 / UNS S30415) data sheet — Outokumpu (2023)
- ASM Handbook Vol. 1 — Properties and Selection: Irons, Steels and High-Performance Alloys — ASM International (1990)
- ASTM A240/A240M — Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip (S30415) — ASTM (2023)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.