Stainless Steel 317LN
AISI/SAE 317LN · UNS S31753
317LN (UNS S31753) is a low-carbon, nitrogen-strengthened 317-type austenitic stainless steel that combines the molybdenum-based pitting resistance of the 317 family with higher design strength from the nitrogen addition.
Reference datasheet — 317LN is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the Annealed condition
317LN tempers and conditions
317LN is supplied in 7 conditions, soft to hard. Annealed is the default FabDigit quotes; the values on this page are for it.
Compare all 7 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
AnnealedDefault solution annealed and quenched (1040–1120 °C, rapid cool) | Standard stocked condition for plate, sheet, pipe and bar; maximum corrosion resistance and ductility. | 320 | 620 | 48 | 170 HB | — |
autogenous/filler weld metal and HAZ, no post-weld anneal | Represents fabricated weldments; low carbon and N keep sensitisation risk low but weld metal ferrite/δ affects toughness. | 330 | 600 | 35 | 185 HB | 2.2 % IACS |
annealed then cold drawn bar/wire (light draft) | Choose for straight, close-tolerance bar with a strength bump over annealed; slightly reduced ductility. | 500 | 720 | 30 | 18 HRC | 2.2 % IACS |
Quarter hard | Light cold-rolled strip/sheet where extra yield strength is needed but some bending is still required. | 620 | 900 | 20 | 25 HRC | 2.2 % IACS |
Half hard | Structural strip/sheet needing high yield with only mild forming; springback and magnetic permeability rise. | 790 | 1,035 | 12 | 32 HRC | 2.2 % IACS |
Three-quarter hard | Flat parts and clips requiring very high yield with essentially no forming. | 930 | 1,170 | 8 | 36 HRC | 2.2 % IACS |
heavily cold rolled strip | Maximum strength thin strip for shims and flat springs; not formable, most magnetic condition. | 1,000 | 1,280 | 6 | 40 HRC | 2.2 % IACS |
What is 317LN?
317LN (UNS S31753) is a low-carbon, nitrogen-strengthened 317-type austenitic stainless steel that combines the molybdenum-based pitting resistance of the 317 family with higher design strength from the nitrogen addition. Annealed material provides 320 MPa yield, 620 MPa tensile, 48 % elongation and 170 HB (88 HRB), with rated service to 425 °C; it is stocked as annealed plate and sheet, cold-drawn bar and quarter- to full-hard cold-worked product. Low carbon avoids sensitization so no post-weld anneal is needed, but machinability is poor (score 32) and forming loads are high. Choose 317LMN when higher molybdenum and nitrogen are required. 317LN has a density of 7.98 g/cm³ (0.288 lb/in³), heavier than 85% of stainless steel grades. It melts at 1,375°C (2,507 °F). 317LN has a yield strength of 320 MPa (46.4 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 60% of stainless steel grades. Elongation at break is 48% and the elastic modulus is 200 GPa (29 Msi).
What is 317LN used for?
- chemical processing
- pressure vessels
- pulp and paper equipment
Advantages
- Polishes to a fine finish — 80/100, better than 89% of stainless steel grades
- Readily welded — 85/100, better than 87% of stainless steel grades
- Tough — resists crack growth — 200 MPa·√m (182 ksi·√in), better than 86% of stainless steel grades
- Ductile — tolerates forming and impact — 48%, better than 85% of stainless steel grades
- Good corrosion resistance — 78/100, better than 84% of stainless steel grades
317LN properties
Typical room-temperature values for 317LN-Annealed; bars are the position among stainless steel grades.
Physical3
317LN has a density of 7.98 g/cm³ (0.288 lb/in³), heavier than 85% of stainless steel grades. It melts at 1,375°C (2,507 °F).
Mechanical16
317LN has a yield strength of 320 MPa (46.4 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 60% of stainless steel grades. Elongation at break is 48% and the elastic modulus is 200 GPa (29 Msi).
Thermal6
317LN is rated for continuous service to 425°C (797 °F). It conducts heat at 14.5 W/m·K (8.38 BTU/hr·ft·°F), worse than 72% of stainless steel grades. Thermal expansion is 16 µm/m·K (8.89 µin/in·°F).
Electrical3
317LN conducts electricity at 2.2 % IACS, worse than 61% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is very good (78/100), better than 84% of stainless steel grades.
Sustainability4
Producing a kilogram of 317LN takes about 60 MJ of energy and emits 4.5 kg of CO₂ — more than 70% of stainless steel grades. Typical recycled content is 65%.
Manufacturability8
317LN's machinability is poor (32/100, worse than 62% of stainless steel grades); weldability excellent (85/100); formability very good (72/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the stainless steel family
Yield strength against density for every stainless steel grade FabDigit runs. 317LN is highlighted; hover a dot for its name, or open the interactive family chart.
Working with 317LN
Is 317LN easy to machine?
Gummy and strongly work-hardening — use rigid setups, positive-rake carbide, heavy positive feed, 20–35 % lower speeds than 304 and flood coolant.
Can 317LN be welded?
Excellent with GTAW/GMAW/SMAW using 317L/317LMn or overalloyed 625-type filler; keep heat input low, interpass <150 °C, no post-weld anneal needed for corrosion service.
Can 317LN be formed, bent or molded?
Cold forms well but nitrogen raises yield and springback versus 317L — allow higher press tonnage and generous bend radii; hot work 1150–1200 °C then solution anneal and water quench.
317LN chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Clow carbon for intergranular corrosion resistance | ≤ 0.03 | 0.02 |
| Mn | ≤ 2 | 1.5 |
| Si | ≤ 0.75 | 0.5 |
| P | ≤ 0.05 | 0.03 |
| S | ≤ 0.03 | 0 |
| Cr | 18 – 20 | 18.7 |
| Ni | 11 – 15 | 13 |
| Mo | 3 – 4 | 3.3 |
| Nsolid-solution strengthening + pitting resistance | 0.1 – 0.22 | 0.15 |
| Fe | balance |
What surface finishes work on 317LN?
Pickle and passivate (ASTM A967) or electropolish after fabrication to restore the passive film; not anodizable, polishes to No.4/mirror finishes.
Surface treatments FabDigit runs on stainless steel parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Passivation
Organic Coating
Thermal Spray
Equivalent designations
Standards and trade names that resolve to Stainless Steel 317LN in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- UNS
- S31753
How much does 317LN cost?
317LN is a premium-cost stainless steel ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
317LN — frequently asked
What is 317LN used for?
317LN is typically used for chemical processing, pressure vessels and pulp and paper equipment. In short: higher-strength 317L; no post-weld anneal needed; nitrogen-boosted pitting resistance.
What is the yield strength of 317LN?
317LN has a typical yield strength of 320 MPa (46.4 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 60% of stainless steel grades. Strength varies by condition: see the 7 listed tempers.
Is 317LN easy to machine?
Not especially — machinability is rated poor (32/100, worse than 62% of stainless steel grades). Gummy and strongly work-hardening — use rigid setups, positive-rake carbide, heavy positive feed, 20–35 % lower speeds than 304 and flood coolant.
Can 317LN be welded?
Yes — weldability is rated excellent (85/100). Excellent with GTAW/GMAW/SMAW using 317L/317LMn or overalloyed 625-type filler; keep heat input low, interpass <150 °C, no post-weld anneal needed for corrosion service.
What surface finishes work on 317LN?
Pickle and passivate (ASTM A967) or electropolish after fabrication to restore the passive film; not anodizable, polishes to No.4/mirror finishes.
Can 317LN be formed, bent or molded?
Cold forms well but nitrogen raises yield and springback versus 317L — allow higher press tonnage and generous bend radii; hot work 1150–1200 °C then solution anneal and water quench.
What is the maximum service temperature of 317LN?
317LN is rated for continuous use to about 425°C (797 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
How much does 317LN cost?
317LN is a premium-cost stainless steel ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- ASTM A240/A240M — Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip — ASTM International (2023)
- ASTM A312/A312M — Seamless and Welded Austenitic Stainless Steel Pipes (TP317LN) — ASTM International (2022)
- ASTM A666 — Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate and Flat Bar — ASTM International (2015)
- GB/T 24511 / GB/T 4237 — SAC (2017)
- ASM Handbook Vol. 1 — Properties and Selection: Irons, Steels and High-Performance Alloys — ASM International (1990)
- Austenitic stainless 317L/317LN data sheets — Outokumpu / Sandvik (2021)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.