Stainless Steel Nitronic 60 · supply condition
Stainless Steel Nitronic 60 Cold Drawn
Properties of the Cold Drawn condition, compared with the other Nitronic 60 tempers.
Choose for precision-diameter bar, valve stems and pins needing ~700 MPa yield with good surface finish and straightness.
What is Nitronic 60 Cold Drawn?
Nitronic 60 Cold Drawn is Nitronic 60 supplied in the Cold Drawn condition — choose for precision-diameter bar, valve stems and pins needing ~700 MPa yield with good surface finish and straightness. Nitronic 60 Cold Drawn has a yield strength of 760 MPa (110 ksi) and a tensile strength of 965 MPa (140 ksi) — stronger than 94% of stainless steel grades. Elongation at break is 25% and the elastic modulus is 196 GPa (28.4 Msi). Nitronic 60 Cold Drawn has a density of 7.63 g/cm³ (0.276 lb/in³), lighter than 96% of stainless steel grades. It melts at 1,343°C (2,449 °F). Solution Annealed is the default condition FabDigit quotes; Cold Drawn is available on request or by drawing note.
Advantages
- High strength — 760 MPa (110 ksi), better than 94% of stainless steel grades
- High service temperature — 870°C (1,598 °F), better than 82% of stainless steel grades
Limitations
- Poor heat conductor — 12.9 W/m·K (7.45 BTU/hr·ft·°F), worse than 86% of stainless steel grades
- Hard to polish — 60/100, worse than 80% of stainless steel grades
Nitronic 60 Cold Drawn properties
Typical room-temperature values for Nitronic 60 Cold Drawn — 11 properties are specific to this condition; the rest are grade-level values shared by every Nitronic 60 temper. Each bar shows where the value sits among the stainless steel grades in FabDigit's library — further right is higher.
Physical3
Nitronic 60 Cold Drawn has a density of 7.63 g/cm³ (0.276 lb/in³), lighter than 96% of stainless steel grades. It melts at 1,343°C (2,449 °F).
Mechanical14
Nitronic 60 Cold Drawn has a yield strength of 760 MPa (110 ksi) and a tensile strength of 965 MPa (140 ksi) — stronger than 94% of stainless steel grades. Elongation at break is 25% and the elastic modulus is 196 GPa (28.4 Msi).
Thermal5
Nitronic 60 Cold Drawn is rated for continuous service to 870°C (1,598 °F). It conducts heat at 12.9 W/m·K (7.45 BTU/hr·ft·°F), worse than 86% of stainless steel grades. Thermal expansion is 15.5 µm/m·K (8.61 µin/in·°F).
Electrical3
Nitronic 60 Cold Drawn conducts electricity at 2.2 % IACS, worse than 61% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is good (58/100), worse than 63% of stainless steel grades.
Sustainability4
Producing a kilogram of Nitronic 60 Cold Drawn takes about 53 MJ of energy and emits 4.5 kg of CO₂ — less than 67% of stainless steel grades. Typical recycled content is 55%.
Manufacturability7
Nitronic 60 Cold Drawn's machinability is poor (28/100, worse than 80% of stainless steel grades); weldability very good (72/100); formability fair (35/100).
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Other Nitronic 60 tempers and conditions
Nitronic 60 is also supplied in 4 other conditions. The full side-by-side table is on the Nitronic 60 overview.
- Solution AnnealedDefaultDefault stocked condition for bar, plate and forgings: maximum ductility and corrosion resistance with ~2× the yield strength of 304 and full galling resistance.414 MPa yield · 210 HB
- Cold Worked HSUse where maximum strength and wear resistance are needed (fasteners, springs, high-load pins); ductility and toughness are reduced.1,000 MPa yield · 35 HRC
- Cold DrawnChoose for precision-diameter bar, valve stems and pins needing ~700 MPa yield with good surface finish and straightness.760 MPa yield · 30 HRC
- AnnealedPick for sheet, strip, screen wire and formed parts where cold formability and weldability matter more than strength.448 MPa yield · 215 HB
Working with Nitronic 60 Cold Drawn
Is Nitronic 60 easy to machine?
Gummy and strongly work-hardening — run 30–50 % of 304 speeds with rigid setups, positive-rake sharp carbide, heavy constant feed to stay under the hardened skin, and copious high-lubricity coolant.
Can Nitronic 60 be welded?
Readily welded by GTAW/GMAW/SMAW with matching Nitronic 60 filler (or 209/240 types); no preheat or post-weld heat treatment needed, keep interpass temperature low and use low heat input to limit distortion.
Can Nitronic 60 be formed, bent or molded?
Cold forms and bends well when allowance is made for the high work-hardening rate (higher press loads, generous bend radii, intermediate anneals for severe draws); hot works at 1010–1200 °C.
What surface finishes work on Nitronic 60?
Passivate per ASTM A967 or electropolish for best corrosion performance; takes a good mechanical polish, and no coating is needed for anti-galling function — do not attempt anodizing.
Nitronic 60 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| C | ≤ 0.1 | 0.06 |
| Mn | 7 – 9 | 8 |
| Sihigh Si gives the galling/wear resistance | 3.5 – 4.5 | 4 |
| Cr | 16 – 18 | 17 |
| Ni | 8 – 9 | 8.5 |
| Ninterstitial strengthener | 0.08 – 0.18 | 0.13 |
| P | ≤ 0.06 | — |
| S | ≤ 0.03 | — |
| Fe | balance | — |
Nitronic 60 Cold Drawn — frequently asked
What is Nitronic 60 Cold Drawn used for?
Nitronic 60 Cold Drawn is typically used for anti-galling fasteners and threaded parts, valve stems, seats and trim, bushings, pins and wear pads, pump and mixer shafts, screens and wear plates and marine deck hardware. In short: high-hardness galling resistant.
What is the yield strength of Nitronic 60 Cold Drawn?
Nitronic 60 Cold Drawn has a typical yield strength of 760 MPa (110 ksi) and a tensile strength of 965 MPa (140 ksi) — stronger than 94% of stainless steel grades. Strength varies by condition: see the 5 listed tempers.
Is Nitronic 60 Cold Drawn easy to machine?
Not especially — machinability is rated poor (28/100, worse than 80% of stainless steel grades). Gummy and strongly work-hardening — run 30–50 % of 304 speeds with rigid setups, positive-rake sharp carbide, heavy constant feed to stay under the hardened skin, and copious high-lubricity coolant.
Can Nitronic 60 Cold Drawn be welded?
Yes — weldability is rated very good (72/100). Readily welded by GTAW/GMAW/SMAW with matching Nitronic 60 filler (or 209/240 types); no preheat or post-weld heat treatment needed, keep interpass temperature low and use low heat input to limit distortion.
What surface finishes work on Nitronic 60 Cold Drawn?
Passivate per ASTM A967 or electropolish for best corrosion performance; takes a good mechanical polish, and no coating is needed for anti-galling function — do not attempt anodizing.
Can Nitronic 60 Cold Drawn be formed, bent or molded?
Cold forms and bends well when allowance is made for the high work-hardening rate (higher press loads, generous bend radii, intermediate anneals for severe draws); hot works at 1010–1200 °C.
What is the maximum service temperature of Nitronic 60 Cold Drawn?
Nitronic 60 Cold Drawn is rated for continuous use to about 870°C (1,598 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in Nitronic 60 Cold Drawn?
Yes — Nitronic 60 Cold Drawn is available for CNC machining and sheet metal with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- ASTM A276/A276M — Stainless Steel Bars and Shapes (UNS S21800) — ASTM International (2017)
- ASTM A479/A479M — Stainless Steel Bars and Shapes for Boilers and Pressure Vessels — ASTM International (2021)
- ASTM A240/A240M — Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip — ASTM International (2023)
- Nitronic 60 (UNS S21800) Product Data Bulletin — AK Steel / Armco (Cleveland-Cliffs) (2019)
- Nitronic 60 High-Strength Anti-Galling Stainless Bar — Universal Stainless / Electralloy (2021)
- ASM Handbook Vol. 1 — Properties and Selection: Irons, Steels and High-Performance Alloys — ASM International (1990)
- ASM Handbook Vol. 13B — Corrosion: Materials — ASM International (2005)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.