Stainless Steel E317-16
Grade
EN E317 · UNS W31710
E317-16 = rutile (titania) coating, AC or DCEP, all position
The most widely stocked type: smooth arc, easy slag release and good bead appearance for all-position general fabrication.
Values for the E317-16 condition
Other E317 tempers and conditions
E317 is listed in 4 conditions; see the grade overview at E317.
Compare all 4 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Rutile-silica coating, AC or DCEP, high deposition | Choose for flatter, wider beads and higher deposition rate on flat/horizontal fillets; slightly more fluid slag than -16. | 430 | 595 | 40 | 180 HB | 2.2 % IACS |
AWDefault As-welded deposit | Default condition: properties of the undiluted deposit in the as-welded state, no post-weld heat treatment. | 440 | 600 | 38 | 185 HB | 2.2 % IACS |
E317-16This page Rutile (titania) coating, AC or DCEP, all position | The most widely stocked type: smooth arc, easy slag release and good bead appearance for all-position general fabrication. | 440 | 605 | 38 | 185 HB | 2.2 % IACS |
Lime (basic) coating, DCEP only | Pick for the cleanest, lowest-oxygen deposit and best impact toughness on heavy or restrained joints; DC electrode positive only. | 450 | 595 | 36 | 185 HB | 2.2 % IACS |
What is E317-16?
E317-16 is E317 in the E317-16 grade — the most widely stocked type: smooth arc, easy slag release and good bead appearance for all-position general fabrication. E317-16 has a yield strength of 440 MPa (63.8 ksi) and a tensile strength of 605 MPa (87.7 ksi) — stronger than 68% of stainless steel grades. Elongation at break is 38% and the elastic modulus is 195 GPa (28.3 Msi). E317-16 has a density of 7.98 g/cm³ (0.288 lb/in³), heavier than 85% of stainless steel grades. It melts at 1,370°C (2,498 °F). AW is the default condition FabDigit quotes; E317-16 is available on request or by drawing note.
Advantages
- Readily welded — 86/100, better than 89% of stainless steel grades
- Good corrosion resistance — 74/100, better than 78% of stainless steel grades
E317-16 properties
Typical room-temperature values for E317-16; 22 are specific to this condition. Other listed values are E317 reference data and may not represent this condition. Bars are the position among stainless steel grades.
Physical3
E317-16 has a density of 7.98 g/cm³ (0.288 lb/in³), heavier than 85% of stainless steel grades. It melts at 1,370°C (2,498 °F).
Mechanical16
E317-16 has a yield strength of 440 MPa (63.8 ksi) and a tensile strength of 605 MPa (87.7 ksi) — stronger than 68% of stainless steel grades. Elongation at break is 38% and the elastic modulus is 195 GPa (28.3 Msi).
Thermal6
E317-16 is rated for continuous service to 760°C (1,400 °F). It conducts heat at 14.4 W/m·K (8.32 BTU/hr·ft·°F), worse than 75% of stainless steel grades. Thermal expansion is 16 µm/m·K (8.89 µin/in·°F).
Electrical3
E317-16 conducts electricity at 2.2 % IACS, worse than 61% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is very good (74/100), better than 78% of stainless steel grades.
Sustainability4
Producing a kilogram of E317-16 takes about 62 MJ of energy and emits 5.2 kg of CO₂ — more than 75% of stainless steel grades. Typical recycled content is 60%.
Manufacturability7
E317-16's machinability is poor (33/100, worse than 57% of stainless steel grades); weldability excellent (86/100); formability good (55/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with E317-16
Is E317 easy to machine?
Weld deposit machines like 317 stainless: gummy and work-hardening — use sharp positive-rake carbide, rigid setup, heavy feed and flood coolant.
Can E317 be welded?
SMAW with short arc, stringer beads and interpass ≤150 °C; keep 4–10 FN delta ferrite for hot-cracking resistance; redry electrodes (≈250–300 °C, 1 h for -15 basic type) before use.
Can E317 be formed, bent or molded?
Not a wrought product; the deposit is ductile (≈38 % elongation) and tolerates weld-repair peening and light straightening.
What surface finishes work on E317?
Grind, pickle and passivate (ASTM A380/A967) or brush with stainless-only tools to restore the passive film; do not anodize.
E317 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Cuse E317L (0.04 max) where sensitization matters | ≤ 0.08 | 0.06 |
| Cr | 18 – 21 | 19.5 |
| Ni | 12 – 14 | 13 |
| Mo | 3 – 4 | 3.5 |
| Mn | 0.5 – 2.5 | 1.6 |
| Si | ≤ 0.9 | 0.5 |
| P | ≤ 0.04 | — |
| S | ≤ 0.03 | — |
| Cu | ≤ 0.75 | — |
| Feremainder of undiluted weld metal | balance | — |
E317-16 — frequently asked
What is E317-16 used for?
E317-16 is typically used for pulp and paper equipment, chemical process vessels and flue gas desulfurization systems. In short: higher Mo than E316; improved pitting resistance; chloride and acid service filler.
What is the yield strength of E317-16?
E317-16 has a typical yield strength of 440 MPa (63.8 ksi) and a tensile strength of 605 MPa (87.7 ksi) — stronger than 68% of stainless steel grades. Strength varies by condition: see the 4 listed tempers.
Is E317-16 easy to machine?
Not especially — machinability is rated poor (33/100, worse than 57% of stainless steel grades). Weld deposit machines like 317 stainless: gummy and work-hardening — use sharp positive-rake carbide, rigid setup, heavy feed and flood coolant.
Can E317-16 be welded?
Yes — weldability is rated excellent (86/100). SMAW with short arc, stringer beads and interpass ≤150 °C; keep 4–10 FN delta ferrite for hot-cracking resistance; redry electrodes (≈250–300 °C, 1 h for -15 basic type) before use.
What surface finishes work on E317-16?
Grind, pickle and passivate (ASTM A380/A967) or brush with stainless-only tools to restore the passive film; do not anodize.
Can E317-16 be formed, bent or molded?
Not a wrought product; the deposit is ductile (≈38 % elongation) and tolerates weld-repair peening and light straightening.
What is the maximum service temperature of E317-16?
E317-16 is rated for continuous use to about 760°C (1,400 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between E317-AW and E317-15?
AW is the default condition — default condition: properties of the undiluted deposit in the as-welded state, no post-weld heat treatment. E317-15: pick for the cleanest, lowest-oxygen deposit and best impact toughness on heavy or restrained joints; DC electrode positive only. Yield strength is 440 MPa in AW versus 450 MPa in E317-15.
Sources
- AWS A5.4/A5.4M — Specification for Stainless Steel Electrodes for Shielded Metal Arc Welding — American Welding Society (2012)
- ASM Handbook Vol.6 — Welding, Brazing and Soldering — ASM International (1993)
- ASM Handbook Vol.1 — Properties and Selection: Irons, Steels and High-Performance Alloys — ASM International (1990)
- Stainless SMAW electrode datasheets (317/317L type) — Böhler Welding / ESAB / Lincoln Electric (2023)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.