Stainless Steel 201 Cold Rolled
Supply condition
AISI/SAE 201 · UNS S20100 · EN 1.4372 · JIS SUS201 · GB 12Cr17Mn6Ni5N
Choose for stiffer, flatter decorative sheet and tube that still bends and roll-forms.
Values for the Cold Rolled condition
Other 201 tempers and conditions
201 is listed in 7 conditions; see the grade overview at 201.
Compare all 7 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Hot Rolled Annealed & Pickled (HRAP, No.1) plate/coil | Pick for thicker plate and structural/industrial parts where surface finish is unimportant. | 360 | 730 | 50 | 170 HB | 2.5 % IACS |
AnnealedDefault solution annealed (1050–1100 °C, rapid cool), 2B/No.1 finish | Default stocked condition for forming, drawing, welding and decorative sheet/tube. | 380 | 750 | 52 | 190 HB | — |
Cold RolledThis page temper/skin-pass rolled (≈1/8 hard) sheet, strip and tube | Choose for stiffer, flatter decorative sheet and tube that still bends and roll-forms. | 480 | 850 | 42 | 21 HRC | 2.5 % IACS |
Quarter hard | Use when moderate strength is needed but some bending/forming must remain possible. | 570 | 900 | 30 | 28 HRC | 2.5 % IACS |
Half hard | Good balance of high strength and limited bendability for brackets, clips and structural strip. | 830 | 1,100 | 18 | 36 HRC | 2.5 % IACS |
Three-quarter hard | For flat spring-like strip and high-strength stampings with only slight forming. | 1,000 | 1,260 | 12 | 40 HRC | 2.5 % IACS |
cold rolled to ASTM A666 full-hard temper | Maximum strength/stiffness thin strip for springs, shims and blades; essentially not formable. | 1,100 | 1,350 | 9 | 43 HRC | — |
What is 201 Cold Rolled?
201 Cold Rolled is 201 supplied in the Cold Rolled condition — choose for stiffer, flatter decorative sheet and tube that still bends and roll-forms. 201 Cold Rolled has a yield strength of 480 MPa (69.6 ksi) and a tensile strength of 850 MPa (123 ksi) — stronger than 75% of stainless steel grades. Elongation at break is 42% and the elastic modulus is 197 GPa (28.6 Msi). 201 Cold Rolled has a density of 7.8 g/cm³ (0.282 lb/in³), heavier than 50% of stainless steel grades. It melts at 1,400°C (2,552 °F). Annealed is the default condition FabDigit quotes; Cold Rolled is available on request or by drawing note.
Advantages
- Easy to machine — 45/100, better than 84% of stainless steel grades
- High strength — 480 MPa (69.6 ksi), better than 75% of stainless steel grades
Limitations
- Limited service temperature — 400°C (752 °F), worse than 78% of stainless steel grades
- Needs corrosion protection — 50/100, worse than 78% of stainless steel grades
201 Cold Rolled properties
Typical room-temperature values for 201 Cold Rolled; 25 are specific to this condition. Other listed values are 201 reference data and may not represent this condition. Bars are the position among stainless steel grades.
Physical3
201 Cold Rolled has a density of 7.8 g/cm³ (0.282 lb/in³), heavier than 50% of stainless steel grades. It melts at 1,400°C (2,552 °F).
Mechanical15
201 Cold Rolled has a yield strength of 480 MPa (69.6 ksi) and a tensile strength of 850 MPa (123 ksi) — stronger than 75% of stainless steel grades. Elongation at break is 42% and the elastic modulus is 197 GPa (28.6 Msi).
Thermal6
201 Cold Rolled is rated for continuous service to 400°C (752 °F). It conducts heat at 16.2 W/m·K (9.36 BTU/hr·ft·°F), better than 64% of stainless steel grades. Thermal expansion is 16 µm/m·K (8.89 µin/in·°F).
Electrical3
201 Cold Rolled conducts electricity at 2.5 % IACS, better than 75% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is fair (50/100), worse than 78% of stainless steel grades.
Sustainability4
Producing a kilogram of 201 Cold Rolled takes about 42 MJ of energy and emits 4 kg of CO₂ — less than 95% of stainless steel grades. Typical recycled content is 55%.
Manufacturability7
201 Cold Rolled's machinability is fair (45/100, better than 84% of stainless steel grades); weldability good (55/100); formability good (65/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with 201 Cold Rolled
Is 201 easy to machine?
Gummy and strongly work-hardening — use rigid setups, sharp positive-rake carbide, heavy flood coolant, constant feed and low-to-moderate speed; expect ~40 % of 1212 rates.
Can 201 be welded?
Weld with 308L/209 filler by GTAW/GMAW or resistance spot; keep heat input low, avoid crater cracks, and provide good fume extraction because of the high manganese.
Can 201 be formed, bent or molded?
Excellent deep-draw and roll-forming behaviour thanks to a high n-value, but plan for high press loads and large springback; interstage annealing helps on severe draws.
What surface finishes work on 201?
Takes No.4, hairline, mirror (8K), electropolish and PVD colour finishes well; passivate after fabrication and keep away from chloride cleaners — it stains far more easily than 304.
201 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| CS20100; 201LN variants ≤0.03 | ≤ 0.15 | 0.08 |
| MnEN 1.4372: 6.0–8.0 | 5.5 – 7.5 | 6.5 |
| Si | ≤ 1 | 0.5 |
| P | ≤ 0.06 | 0.03 |
| S | ≤ 0.03 | 0.01 |
| Cr | 16 – 18 | 17 |
| Nicommodity 201 often runs 1.0-4.0 Ni (low-nickel 201) | 3.5 – 5.5 | 4.5 |
| NEN 1.4372: 0.05–0.25 | ≤ 0.25 | 0.15 |
| Cunot in ASTM limits; common residual/intentional in Chinese 201 | ≤ 1 | 0.4 |
| Fe | balance |
201 Cold Rolled — frequently asked
What is 201 Cold Rolled used for?
201 Cold Rolled is typically used for cookware, automotive trim and architectural panels. In short: lower-cost austenitic stainless.
What is the yield strength of 201 Cold Rolled?
201 Cold Rolled has a typical yield strength of 480 MPa (69.6 ksi) and a tensile strength of 850 MPa (123 ksi) — stronger than 75% of stainless steel grades. Strength varies by condition: see the 7 listed tempers.
Is 201 Cold Rolled easy to machine?
Reasonably — machinability is rated fair (45/100, better than 84% of stainless steel grades). Gummy and strongly work-hardening — use rigid setups, sharp positive-rake carbide, heavy flood coolant, constant feed and low-to-moderate speed; expect ~40 % of 1212 rates.
Can 201 Cold Rolled be welded?
Yes — weldability is rated good (55/100). Weld with 308L/209 filler by GTAW/GMAW or resistance spot; keep heat input low, avoid crater cracks, and provide good fume extraction because of the high manganese.
What surface finishes work on 201 Cold Rolled?
Takes No.4, hairline, mirror (8K), electropolish and PVD colour finishes well; passivate after fabrication and keep away from chloride cleaners — it stains far more easily than 304.
Can 201 Cold Rolled be formed, bent or molded?
Excellent deep-draw and roll-forming behaviour thanks to a high n-value, but plan for high press loads and large springback; interstage annealing helps on severe draws.
What is the maximum service temperature of 201 Cold Rolled?
201 Cold Rolled is rated for continuous use to about 400°C (752 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in 201 Cold Rolled?
Yes — 201 Cold Rolled is available for CNC machining and sheet metal with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- ASTM A666 — Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate and Flat Bar — ASTM International (2015)
- ASTM A240/A240M — ASTM International (2023)
- EN 10088-1/-2 (X12CrMnNiN17-7-5, 1.4372) — CEN (2014)
- GB/T 3280 (1Cr17Mn6Ni5N / 201) — SAC (2015)
- ASM Specialty Handbook: Stainless Steels — ASM International (1994)
- ASM Handbook Vol.1 & Vol.13B — ASM International (2005)
- Cr-Mn austenitic stainless (Outokumpu / Yieh United / Baosteel Desheng 201 datasheets) — various producers (2023)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.