Copper Alloy C95200 M07-AsCast
Heat-treated state
UNS C95200
Continuous-cast bar/tube stock for machined bushings and wear parts; sound, low-porosity sections.
Values for the M07-AsCast condition
Other C95200 tempers and conditions
C95200 is listed in 4 conditions; see the grade overview at C95200.
- M01-AsCast
- M02-AsCast
- M07-AsCast
- TQ50
Compare all 4 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
M01-AsCastDefault M01 | Standard stocked condition for pump/valve bodies and general hardware; best ductility, lowest cost. | 207 | 552 | 30 | 115 HB | 12 % IACS |
M02 | Pick for bushings, sleeves and rings — denser, finer structure gives higher strength than sand casting. | 241 | 586 | 25 | 125 HB | 12 % IACS |
M07-AsCastThis page M07 | Continuous-cast bar/tube stock for machined bushings and wear parts; sound, low-porosity sections. | 241 | 586 | 25 | 125 HB | 12 % IACS |
Quenched from ~815 °C and temper annealed | Choose when higher yield strength and hardness are needed for gears, wear plates and heavily loaded bushings. | 276 | 621 | 20 | 143 HB | 12 % IACS |
What is C95200 M07-AsCast?
C95200 M07-AsCast is C95200 heat treated to M07-AsCast — continuous-cast bar/tube stock for machined bushings and wear parts; sound, low-porosity sections. C95200 M07-AsCast has a yield strength of 241 MPa (35 ksi) and a tensile strength of 586 MPa (85 ksi) — stronger than 53% of copper alloy grades. Elongation at break is 25% and the elastic modulus is 110 GPa (16 Msi). C95200 M07-AsCast has a density of 7.64 g/cm³ (0.276 lb/in³), lighter than 92% of copper alloy grades. It melts at 1,043°C (1,909 °F). M01-AsCast is the default condition FabDigit quotes; M07-AsCast is available on request or by drawing note.
Advantages
- Lightweight — 7.64 g/cm³ (0.276 lb/in³), better than 92% of copper alloy grades
- High service temperature — 300°C (572 °F), better than 85% of copper alloy grades
- Readily welded — 70/100, better than 85% of copper alloy grades
C95200 M07-AsCast properties
Typical room-temperature values for C95200 M07-AsCast; 21 are specific to this condition. Other listed values are C95200 reference data and may not represent this condition. Bars are the position among copper alloy grades.
Physical3
C95200 M07-AsCast has a density of 7.64 g/cm³ (0.276 lb/in³), lighter than 92% of copper alloy grades. It melts at 1,043°C (1,909 °F).
Mechanical15
C95200 M07-AsCast has a yield strength of 241 MPa (35 ksi) and a tensile strength of 586 MPa (85 ksi) — stronger than 53% of copper alloy grades. Elongation at break is 25% and the elastic modulus is 110 GPa (16 Msi).
Thermal6
C95200 M07-AsCast is rated for continuous service to 300°C (572 °F). It conducts heat at 58.6 W/m·K (33.9 BTU/hr·ft·°F), worse than 63% of copper alloy grades. Thermal expansion is 16.2 µm/m·K (9 µin/in·°F).
Electrical3
C95200 M07-AsCast conducts electricity at 12 % IACS, worse than 62% of copper alloy grades.
Chemical & Environmental3
Corrosion resistance is very good (70/100), better than 76% of copper alloy grades.
Sustainability4
Producing a kilogram of C95200 M07-AsCast takes about 52 MJ of energy and emits 3.6 kg of CO₂ — less than 87% of copper alloy grades. Typical recycled content is 55%.
Manufacturability8
C95200 M07-AsCast's machinability is fair (45/100, better than 64% of copper alloy grades); weldability very good (70/100); formability poor (20/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with C95200 M07-AsCast
Is C95200 easy to machine?
Machines like a tough gummy bronze at ~50 % of free-cutting brass: use sharp positive-rake carbide, rigid setups, moderate speeds with generous coolant to avoid work-hardened skin and built-up edge.
Can C95200 be welded?
GTAW/GMAW with matching aluminium-bronze filler (ERCuAl-A2) works well; keep interpass temperature low, clean the tenacious Al₂O₃ film mechanically before each pass, and avoid oxyacetylene.
Can C95200 be formed, bent or molded?
A casting alloy only — sand, centrifugal and continuous cast; needs quiescent bottom filling, generous chills/risers and oxide-skim control because the oxide film causes lap defects.
What surface finishes work on C95200?
Not anodizable; pickle/passivate or shot-blast then paint, or leave bare for seawater service. Polishes to a golden lustre but tarnishes; electroless nickel or chrome plating requires activation of the aluminium oxide.
C95200 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Alprimary strengthener, forms α+κ structure | 8.5 – 9.5 | 9 |
| Fegrain refiner / κ-phase former | 2.5 – 4 | 3 |
| Mnresidual limit (per B505 named-element practice) | ≤ 0.5 | — |
| Niresidual limit; Ni-bearing service grades are C95500/C95800 | ≤ 1 | — |
| Siresidual limit | ≤ 0.25 | — |
| Cu86 % min per ASTM B148/B505 | ≥ 86 (balance) | — |
C95200 M07-AsCast — frequently asked
What is C95200 M07-AsCast used for?
C95200 M07-AsCast is typically used for valve bodies, gears, bushings and marine hardware. In short: entry-level aluminium bronze; weldable cast bronze; high elongation, 30 %.
What is the yield strength of C95200 M07-AsCast?
C95200 M07-AsCast has a typical yield strength of 241 MPa (35 ksi) and a tensile strength of 586 MPa (85 ksi) — stronger than 53% of copper alloy grades. Strength varies by condition: see the 4 listed tempers.
Is C95200 M07-AsCast easy to machine?
Reasonably — machinability is rated fair (45/100, better than 64% of copper alloy grades). Machines like a tough gummy bronze at ~50 % of free-cutting brass: use sharp positive-rake carbide, rigid setups, moderate speeds with generous coolant to avoid work-hardened skin and built-up edge.
Can C95200 M07-AsCast be welded?
Yes — weldability is rated very good (70/100). GTAW/GMAW with matching aluminium-bronze filler (ERCuAl-A2) works well; keep interpass temperature low, clean the tenacious Al₂O₃ film mechanically before each pass, and avoid oxyacetylene.
What surface finishes work on C95200 M07-AsCast?
Not anodizable; pickle/passivate or shot-blast then paint, or leave bare for seawater service. Polishes to a golden lustre but tarnishes; electroless nickel or chrome plating requires activation of the aluminium oxide.
Can C95200 M07-AsCast be formed, bent or molded?
A casting alloy only — sand, centrifugal and continuous cast; needs quiescent bottom filling, generous chills/risers and oxide-skim control because the oxide film causes lap defects.
What is the maximum service temperature of C95200 M07-AsCast?
C95200 M07-AsCast is rated for continuous use to about 300°C (572 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between C95200 M01-AsCast and C95200-TQ50?
M01-AsCast is the default condition — standard stocked condition for pump/valve bodies and general hardware; best ductility, lowest cost. TQ50: choose when higher yield strength and hardness are needed for gears, wear plates and heavily loaded bushings. Yield strength is 207 MPa in M01-AsCast versus 276 MPa in TQ50.
Sources
- ASTM B148 – Aluminum-Bronze Sand Castings — ASTM International (2019)
- ASTM B505/B505M – Copper Alloy Continuous Castings — ASTM International (2018)
- CDA Alloy Datasheet C95200 — Copper Development Association (copper.org) (2023)
- ASM Handbook Vol. 2 – Properties of Nonferrous Alloys — ASM International (1990)
- GB/T 1176 ZCuAl9Fe4 (2013)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.