Titanium CP-Ti Grade 2 (AM Powder)
UNS R50400 · ASTM F67
CP-Ti Grade 2 (AM Powder) is unalloyed commercially pure titanium powder to F67/R50400 chemistry, used as feedstock for LPBF, EBM, DED, binder jetting and MIM.
Reference datasheet — CP-Ti Grade 2 (AM Powder) is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
CP-Ti Grade 2 (AM Powder) tempers and conditions
CP-Ti Grade 2 (AM Powder) is supplied in 2 conditions, soft to hard.
Compare all 2 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Binder Jet + Vacuum Sintered (~1250–1350 °C) | Choose for higher-volume, lower-cost small parts where 96–99 % density and slightly lower ductility are acceptable. | 350 | 460 | 15 | 157 HB | 2.9 % IACS |
metal injection moulded CP-Ti Grade 2, vacuum sintered | Uses the same fine powder for mass-produced small components (dental, eyewear, connectors); properties per MPIF 35/ASTM F2989 class. | 360 | 450 | 16 | 162 HB | 3 % IACS |
Supply forms, finishes and certifications
Ways CP-Ti Grade 2 (AM Powder) is supplied — form, process route, surface or paperwork — without a datasheet of their own. The property values above apply.
| Option | What it is | Type |
|---|---|---|
DED-AB | DED As-Built | Printing process |
EBM-AB | EBM As-Built | Printing process |
LPBF-ABDefault | L-PBF As-Built | Printing process |
POWDER | Gas-atomized spherical feedstock | Printing process |
LPBF-ANN | L-PBF Annealed | Surface finish |
LPBF-HIP | L-PBF HIP | Surface finish |
LPBF-SR | L-PBF Stress Relieved | Surface finish |
What is CP-Ti Grade 2 (AM Powder)?
CP-Ti Grade 2 (AM Powder) is unalloyed commercially pure titanium powder to F67/R50400 chemistry, used as feedstock for LPBF, EBM, DED, binder jetting and MIM. As-built and post-processed parts reach about 530 MPa yield, 640 MPa tensile and 18 % elongation at 95 HRB, with 16 W/m·K conductivity and service to 300 °C. It is chosen where corrosion resistance and ductility matter more than strength, and where geometry rules out machining from plate. Strength is well below Ti-6Al-4V ELI, machinability is poor (score 35), and powder must be handled dry and inert to limit oxygen and hydrogen pickup. CP-Ti Grade 2 (AM Powder) has a density of 4.51 g/cm³ (0.163 lb/in³), heavier than 57% of titanium grades. It melts at 1,660°C (3,020 °F). CP-Ti Grade 2 (AM Powder) has a yield strength of 530 MPa (76.9 ksi) and a tensile strength of 640 MPa (92.8 ksi) — weaker than 59% of titanium grades. Elongation at break is 18% and the elastic modulus is 105 GPa (15.2 Msi).
What is CP-Ti Grade 2 (AM Powder) used for?
- Dental frameworks
- Chemical process components
- Marine hardware
- Heat exchanger parts
- Medical device housings
Advantages
- Easy to machine — 38/100, better than 85% of titanium grades
- High electrical conductivity — 3.1 % IACS, better than 75% of titanium grades
Limitations
- High embodied carbon — 52 kg CO₂/kg, worse than 99% of titanium grades
CP-Ti Grade 2 (AM Powder) properties
Typical room-temperature values; bars are the position among titanium grades.
Physical3
CP-Ti Grade 2 (AM Powder) has a density of 4.51 g/cm³ (0.163 lb/in³), heavier than 57% of titanium grades. It melts at 1,660°C (3,020 °F).
Mechanical16
CP-Ti Grade 2 (AM Powder) has a yield strength of 530 MPa (76.9 ksi) and a tensile strength of 640 MPa (92.8 ksi) — weaker than 59% of titanium grades. Elongation at break is 18% and the elastic modulus is 105 GPa (15.2 Msi).
Thermal6
CP-Ti Grade 2 (AM Powder) is rated for continuous service to 300°C (572 °F). It conducts heat at 16.4 W/m·K (9.48 BTU/hr·ft·°F), better than 71% of titanium grades. Thermal expansion is 8.6 µm/m·K (4.78 µin/in·°F).
Electrical3
CP-Ti Grade 2 (AM Powder) conducts electricity at 3.1 % IACS, better than 75% of titanium grades.
Chemical & Environmental3
Corrosion resistance is excellent (92/100), better than 53% of titanium grades.
Sustainability4
Producing a kilogram of CP-Ti Grade 2 (AM Powder) takes about 900 MJ of energy and emits 52 kg of CO₂ — more than 99% of titanium grades. Typical recycled content is 20%.
Manufacturability8
CP-Ti Grade 2 (AM Powder)'s machinability is fair (38/100, better than 85% of titanium grades); weldability excellent (88/100); formability very good (70/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the titanium family
Yield strength against density for every titanium grade FabDigit runs. CP-Ti Grade 2 (AM Powder) is highlighted; hover a dot for its name, or open the interactive family chart.
Working with CP-Ti Grade 2 (AM Powder)
Is CP-Ti Grade 2 (AM Powder) easy to machine?
Use sharp uncoated-carbide or PVD tools, low surface speed (30–60 m/min), heavy positive rake, high-pressure flood coolant; never dwell — Ti work-hardens, galls and fine chips/dust are a fire hazard.
Can CP-Ti Grade 2 (AM Powder) be welded?
Excellent GTAW/EBW/LBW weldability provided the weld pool and hot HAZ are fully shielded with argon/helium trailing and backing gas; welds stay ductile, discoloration beyond straw indicates contamination.
Can CP-Ti Grade 2 (AM Powder) be formed, bent or molded?
Parts are net-shape from the printer; recoater/scan strategy plus 600 °C stress relief before plate removal controls warp, and powder must be sieved and handled under low-moisture inert conditions to limit O/H pickup.
CP-Ti Grade 2 (AM Powder) chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| NASTM F67/B348 Grade 2 max | ≤ 0.03 | 0.01 |
| C | ≤ 0.08 | 0.01 |
| Hpowder often held ≤0.010 % | ≤ 0.02 | 0 |
| Fe | ≤ 0.3 | 0.1 |
| Ooxygen rises with powder reuse; control critical | ≤ 0.25 | 0.14 |
| residuals each0.40 % max total | ≤ 0.1 | |
| Ti | balance |
What surface finishes work on CP-Ti Grade 2 (AM Powder)?
Support removal, blasting, tumbling, chemical etch or abrasive-flow polishing to cut as-built Ra 8–20 µm; anodizes to bright interference colors and passivates naturally per ASTM F86 for medical use.
Surface treatments FabDigit runs on titanium parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Thermal Spray
Equivalent designations
Standards and trade names that resolve to Titanium CP-Ti Grade 2 (AM Powder) in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- UNS
- R50400
- ASTM
- F67
- Also called
- Grade 2 AM
How much does CP-Ti Grade 2 (AM Powder) cost?
CP-Ti Grade 2 (AM Powder) is a high-cost titanium ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
CP-Ti Grade 2 (AM Powder) — frequently asked
What is CP-Ti Grade 2 (AM Powder) used for?
CP-Ti Grade 2 (AM Powder) is typically used for dental frameworks, chemical process components, marine hardware, heat exchanger parts and medical device housings. In short: most ductile AM titanium; unalloyed corrosion-resistant powder; medical and chemical duty.
What is the yield strength of CP-Ti Grade 2 (AM Powder)?
CP-Ti Grade 2 (AM Powder) has a typical yield strength of 530 MPa (76.9 ksi) and a tensile strength of 640 MPa (92.8 ksi) — weaker than 59% of titanium grades. Strength varies by condition: see the 2 listed tempers.
Is CP-Ti Grade 2 (AM Powder) easy to machine?
Not especially — machinability is rated fair (38/100, better than 85% of titanium grades). Use sharp uncoated-carbide or PVD tools, low surface speed (30–60 m/min), heavy positive rake, high-pressure flood coolant; never dwell — Ti work-hardens, galls and fine chips/dust are a fire hazard.
Can CP-Ti Grade 2 (AM Powder) be welded?
Yes — weldability is rated excellent (88/100). Excellent GTAW/EBW/LBW weldability provided the weld pool and hot HAZ are fully shielded with argon/helium trailing and backing gas; welds stay ductile, discoloration beyond straw indicates contamination.
What surface finishes work on CP-Ti Grade 2 (AM Powder)?
Support removal, blasting, tumbling, chemical etch or abrasive-flow polishing to cut as-built Ra 8–20 µm; anodizes to bright interference colors and passivates naturally per ASTM F86 for medical use.
Can CP-Ti Grade 2 (AM Powder) be formed, bent or molded?
Parts are net-shape from the printer; recoater/scan strategy plus 600 °C stress relief before plate removal controls warp, and powder must be sieved and handled under low-moisture inert conditions to limit O/H pickup.
What is the maximum service temperature of CP-Ti Grade 2 (AM Powder)?
CP-Ti Grade 2 (AM Powder) is rated for continuous use to about 300°C (572 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
How much does CP-Ti Grade 2 (AM Powder) cost?
CP-Ti Grade 2 (AM Powder) is a high-cost titanium ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- ASTM F67 — Unalloyed Titanium for Surgical Implant Applications — ASTM (2017)
- ASTM B348 / B265 — Titanium and Titanium Alloy Bar and Sheet — ASTM (2021)
- ASTM F3302 — Additive Manufacturing of Titanium Alloys via PBF — ASTM (2018)
- ASM Handbook Vol. 2 — Properties of Nonferrous Alloys (Titanium) — ASM International (1990)
- Materials Properties Handbook: Titanium Alloys — ASM International (1994)
- AM CP-Ti Grade 2 powder / L-PBF process datasheets — EOS, SLM Solutions, AP&C, Carpenter Additive (2023)
- MPIF Standard 35 — Materials Standards for Metal Injection Molded Parts — MPIF (2018)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.