Titanium CP-Ti Grade 2 (AM Powder) MIM-SINT
Print state
UNS R50400 · ASTM F67
Uses the same fine powder for mass-produced small components (dental, eyewear, connectors); properties per MPIF 35/ASTM F2989 class.
Values for the MIM-SINT condition
Other CP-Ti Grade 2 (AM Powder) tempers and conditions
CP-Ti Grade 2 (AM Powder) is listed in 2 conditions; see the grade overview at CP-Ti Grade 2 (AM Powder).
- BJT-SINT
- MIM-SINT
Compare all 2 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Binder Jet + Vacuum Sintered (~1250–1350 °C) | Choose for higher-volume, lower-cost small parts where 96–99 % density and slightly lower ductility are acceptable. | 350 | 460 | 15 | 157 HB | 2.9 % IACS |
MIM-SINTThis page metal injection moulded CP-Ti Grade 2, vacuum sintered | Uses the same fine powder for mass-produced small components (dental, eyewear, connectors); properties per MPIF 35/ASTM F2989 class. | 360 | 450 | 16 | 162 HB | 3 % IACS |
What is CP-Ti Grade 2 (AM Powder) MIM-SINT?
CP-Ti Grade 2 (AM Powder) MIM-SINT is CP-Ti Grade 2 (AM Powder) in the MIM-SINT condition — uses the same fine powder for mass-produced small components (dental, eyewear, connectors); properties per MPIF 35/ASTM F2989 class. CP-Ti Grade 2 (AM Powder) MIM-SINT has a yield strength of 360 MPa (52.2 ksi) and a tensile strength of 450 MPa (65.3 ksi) — weaker than 77% of titanium grades. Elongation at break is 16% and the elastic modulus is 100 GPa (14.5 Msi). CP-Ti Grade 2 (AM Powder) MIM-SINT has a density of 4.4 g/cm³ (0.159 lb/in³), lighter than 98% of titanium grades. It melts at 1,660°C (3,020 °F).
Advantages
- Easy to machine — 40/100, better than 93% of titanium grades
Limitations
- High embodied carbon — 52 kg CO₂/kg, worse than 99% of titanium grades
- Low fracture toughness — 52 MPa·√m (47.3 ksi·√in), worse than 93% of titanium grades
- Low strength — 360 MPa (52.2 ksi), worse than 77% of titanium grades
CP-Ti Grade 2 (AM Powder) MIM-SINT properties
Typical room-temperature values for CP-Ti Grade 2 (AM Powder) MIM-SINT; 23 are specific to this condition. Other listed values are CP-Ti Grade 2 (AM Powder) reference data and may not represent this condition. Bars are the position among titanium grades.
Physical3
CP-Ti Grade 2 (AM Powder) MIM-SINT has a density of 4.4 g/cm³ (0.159 lb/in³), lighter than 98% of titanium grades. It melts at 1,660°C (3,020 °F).
Mechanical16
CP-Ti Grade 2 (AM Powder) MIM-SINT has a yield strength of 360 MPa (52.2 ksi) and a tensile strength of 450 MPa (65.3 ksi) — weaker than 77% of titanium grades. Elongation at break is 16% and the elastic modulus is 100 GPa (14.5 Msi).
Thermal6
CP-Ti Grade 2 (AM Powder) MIM-SINT is rated for continuous service to 300°C (572 °F). It conducts heat at 15.8 W/m·K (9.13 BTU/hr·ft·°F), better than 60% of titanium grades. Thermal expansion is 8.6 µm/m·K (4.78 µin/in·°F).
Electrical3
CP-Ti Grade 2 (AM Powder) MIM-SINT conducts electricity at 3 % IACS, better than 60% of titanium grades.
Chemical & Environmental3
Corrosion resistance is excellent (89/100), worse than 68% of titanium grades.
Sustainability4
Producing a kilogram of CP-Ti Grade 2 (AM Powder) MIM-SINT takes about 900 MJ of energy and emits 52 kg of CO₂ — more than 99% of titanium grades. Typical recycled content is 20%.
Manufacturability8
CP-Ti Grade 2 (AM Powder) MIM-SINT's machinability is fair (40/100, better than 93% of titanium grades); weldability very good (72/100); formability poor (32/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with CP-Ti Grade 2 (AM Powder) MIM-SINT
Is CP-Ti Grade 2 (AM Powder) easy to machine?
Use sharp uncoated-carbide or PVD tools, low surface speed (30–60 m/min), heavy positive rake, high-pressure flood coolant; never dwell — Ti work-hardens, galls and fine chips/dust are a fire hazard.
Can CP-Ti Grade 2 (AM Powder) be welded?
Excellent GTAW/EBW/LBW weldability provided the weld pool and hot HAZ are fully shielded with argon/helium trailing and backing gas; welds stay ductile, discoloration beyond straw indicates contamination.
Can CP-Ti Grade 2 (AM Powder) be formed, bent or molded?
Parts are net-shape from the printer; recoater/scan strategy plus 600 °C stress relief before plate removal controls warp, and powder must be sieved and handled under low-moisture inert conditions to limit O/H pickup.
What surface finishes work on CP-Ti Grade 2 (AM Powder)?
Support removal, blasting, tumbling, chemical etch or abrasive-flow polishing to cut as-built Ra 8–20 µm; anodizes to bright interference colors and passivates naturally per ASTM F86 for medical use.
CP-Ti Grade 2 (AM Powder) chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| NASTM F67/B348 Grade 2 max | ≤ 0.03 | 0.01 |
| C | ≤ 0.08 | 0.01 |
| Hpowder often held ≤0.010 % | ≤ 0.02 | 0 |
| Fe | ≤ 0.3 | 0.1 |
| Ooxygen rises with powder reuse; control critical | ≤ 0.25 | 0.14 |
| residuals each0.40 % max total | ≤ 0.1 | — |
| Ti | balance | — |
CP-Ti Grade 2 (AM Powder) MIM-SINT — frequently asked
What is CP-Ti Grade 2 (AM Powder) MIM-SINT used for?
CP-Ti Grade 2 (AM Powder) MIM-SINT is typically used for dental frameworks, chemical process components, marine hardware, heat exchanger parts and medical device housings. In short: most ductile AM titanium; unalloyed corrosion-resistant powder; medical and chemical duty.
What is the yield strength of CP-Ti Grade 2 (AM Powder) MIM-SINT?
CP-Ti Grade 2 (AM Powder) MIM-SINT has a typical yield strength of 360 MPa (52.2 ksi) and a tensile strength of 450 MPa (65.3 ksi) — weaker than 77% of titanium grades. Strength varies by condition: see the 2 listed tempers.
Is CP-Ti Grade 2 (AM Powder) MIM-SINT easy to machine?
Not especially — machinability is rated fair (40/100, better than 93% of titanium grades). Use sharp uncoated-carbide or PVD tools, low surface speed (30–60 m/min), heavy positive rake, high-pressure flood coolant; never dwell — Ti work-hardens, galls and fine chips/dust are a fire hazard.
Can CP-Ti Grade 2 (AM Powder) MIM-SINT be welded?
Yes — weldability is rated very good (72/100). Excellent GTAW/EBW/LBW weldability provided the weld pool and hot HAZ are fully shielded with argon/helium trailing and backing gas; welds stay ductile, discoloration beyond straw indicates contamination.
What surface finishes work on CP-Ti Grade 2 (AM Powder) MIM-SINT?
Support removal, blasting, tumbling, chemical etch or abrasive-flow polishing to cut as-built Ra 8–20 µm; anodizes to bright interference colors and passivates naturally per ASTM F86 for medical use.
Can CP-Ti Grade 2 (AM Powder) MIM-SINT be formed, bent or molded?
Parts are net-shape from the printer; recoater/scan strategy plus 600 °C stress relief before plate removal controls warp, and powder must be sieved and handled under low-moisture inert conditions to limit O/H pickup.
What is the maximum service temperature of CP-Ti Grade 2 (AM Powder) MIM-SINT?
CP-Ti Grade 2 (AM Powder) MIM-SINT is rated for continuous use to about 300°C (572 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Sources
- ASTM F67 — Unalloyed Titanium for Surgical Implant Applications — ASTM (2017)
- ASTM B348 / B265 — Titanium and Titanium Alloy Bar and Sheet — ASTM (2021)
- ASTM F3302 — Additive Manufacturing of Titanium Alloys via PBF — ASTM (2018)
- ASM Handbook Vol. 2 — Properties of Nonferrous Alloys (Titanium) — ASM International (1990)
- Materials Properties Handbook: Titanium Alloys — ASM International (1994)
- AM CP-Ti Grade 2 powder / L-PBF process datasheets — EOS, SLM Solutions, AP&C, Carpenter Additive (2023)
- MPIF Standard 35 — Materials Standards for Metal Injection Molded Parts — MPIF (2018)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.