Nickel Alloy ERNiCrFe-11-SA (Solution annealed weld metal)
Heat-treated state
also Inconel Filler Metal 152
Applied to weld overlays or clad components that receive a full solution anneal with the base metal; homogenises the dendritic structure and lowers strength.
Values for the SA condition
Other ERNiCrFe-11 tempers and conditions
ERNiCrFe-11 is listed in 3 conditions; see the grade overview at ERNiCrFe-11.
Compare all 3 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
SAThis page Solution annealed weld metal | Applied to weld overlays or clad components that receive a full solution anneal with the base metal; homogenises the dendritic structure and lowers strength. | 330 | 620 | 45 | 175 HB | 1.5 % IACS |
AWDefault As-welded deposit | Standard condition for GTAW/GMAW deposits and overlays used in nuclear DMW joints; no PWHT applied to the nickel weld metal. | 420 | 690 | 40 | 14 HRC | 1.5 % IACS |
Post-weld heat treated | Used when the ferritic side of a dissimilar joint requires PWHT; the Ni weld metal keeps strength but ductility and toughness drop slightly. | 440 | 700 | 35 | 16 HRC | 1.5 % IACS |
What is ERNiCrFe-11-SA?
ERNiCrFe-11-SA is ERNiCrFe-11 heat treated to SA — applied to weld overlays or clad components that receive a full solution anneal with the base metal; homogenises the dendritic structure and lowers strength. ERNiCrFe-11-SA has a yield strength of 330 MPa (47.9 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 67% of nickel alloy grades. Elongation at break is 45% and the elastic modulus is 210 GPa (30.5 Msi). ERNiCrFe-11-SA has a density of 8.19 g/cm³ (0.296 lb/in³), lighter than 68% of nickel alloy grades. It melts at 1,343°C (2,449 °F). AW is the default condition FabDigit quotes; SA is available on request or by drawing note.
Advantages
- Tough — resists crack growth — 215 MPa·√m (195.7 ksi·√in), better than 101% of nickel alloy grades
- Good corrosion resistance — 90/100, better than 85% of nickel alloy grades
- Readily welded — 85/100, better than 83% of nickel alloy grades
- High service temperature — 1,000°C (1,832 °F), better than 79% of nickel alloy grades
ERNiCrFe-11-SA properties
Typical room-temperature values for ERNiCrFe-11-SA; 22 are specific to this condition. Other listed values are ERNiCrFe-11 reference data and may not represent this condition. Bars are the position among nickel alloy grades.
Physical3
ERNiCrFe-11-SA has a density of 8.19 g/cm³ (0.296 lb/in³), lighter than 68% of nickel alloy grades. It melts at 1,343°C (2,449 °F).
Mechanical17
ERNiCrFe-11-SA has a yield strength of 330 MPa (47.9 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 67% of nickel alloy grades. Elongation at break is 45% and the elastic modulus is 210 GPa (30.5 Msi).
Thermal6
ERNiCrFe-11-SA is rated for continuous service to 1,000°C (1,832 °F). It conducts heat at 12.2 W/m·K (7.05 BTU/hr·ft·°F), better than 68% of nickel alloy grades. Thermal expansion is 13.5 µm/m·K (7.5 µin/in·°F).
Electrical3
ERNiCrFe-11-SA conducts electricity at 1.5 % IACS, better than 59% of nickel alloy grades.
Chemical & Environmental3
Corrosion resistance is excellent (90/100), better than 85% of nickel alloy grades.
Sustainability4
Producing a kilogram of ERNiCrFe-11-SA takes about 135 MJ of energy and emits 11.5 kg of CO₂ — less than 84% of nickel alloy grades. Typical recycled content is 25%.
Manufacturability7
ERNiCrFe-11-SA's machinability is poor (20/100, better than 53% of nickel alloy grades); weldability excellent (85/100); formability very good (70/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with ERNiCrFe-11-SA
Is ERNiCrFe-11 easy to machine?
Weld deposits machine like Alloy 690 — tough, work-hardening, needs rigid setups, sharp carbide, low speed and heavy positive feed.
Can ERNiCrFe-11 be welded?
Deposit with GTAW/GMAW/hot-wire, stringer beads, low heat input, interpass typically ≤150 °C and clean surfaces to avoid ductility-dip and hot cracking.
Can ERNiCrFe-11 be formed, bent or molded?
Supplied as drawn spooled wire or cut lengths; the alloy is ductile enough for wire drawing but is not a wrought structural product form.
What surface finishes work on ERNiCrFe-11?
Pickle/passivate or lightly grind and buff; no anodizing, and grinding debris must be kept ferrite-free in nuclear service.
ERNiCrFe-11 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| C | ≤ 0.05 | 0.03 |
| Mnhigh Mn for hot-crack resistance | ≤ 5 | 3.5 |
| Si | ≤ 0.75 | 0.3 |
| P | ≤ 0.02 | — |
| S | ≤ 0.02 | — |
| Cr | 28 – 31.5 | 30 |
| Fe | 7 – 12 | 9.5 |
| Nb+Ta | 1 – 2.5 | 1.8 |
| Ti | ≤ 0.5 | 0.2 |
| Al | ≤ 0.5 | 0.2 |
| Cu | ≤ 0.5 | — |
| Mo | ≤ 0.5 | — |
| Corestricted for nuclear service | ≤ 0.12 | — |
| Other, eachtotal of other elements | ≤ 0.5 | — |
| Nibalance, Ni 54 % min | ≥ 54 (balance) | — |
ERNiCrFe-11-SA — frequently asked
What is ERNiCrFe-11-SA used for?
ERNiCrFe-11-SA is typically used for alloy 690 tube-to-tubesheet welds, nuclear reactor dissimilar-metal welds and steam generator repairs. In short: best SCC-resistant nickel filler; nuclear-grade Alloy 690 match; restricted availability, documented supply.
What is the yield strength of ERNiCrFe-11-SA?
ERNiCrFe-11-SA has a typical yield strength of 330 MPa (47.9 ksi) and a tensile strength of 620 MPa (89.9 ksi) — weaker than 67% of nickel alloy grades. Strength varies by condition: see the 3 listed tempers.
Is ERNiCrFe-11-SA easy to machine?
Not especially — machinability is rated poor (20/100, better than 53% of nickel alloy grades). Weld deposits machine like Alloy 690 — tough, work-hardening, needs rigid setups, sharp carbide, low speed and heavy positive feed.
Can ERNiCrFe-11-SA be welded?
Yes — weldability is rated excellent (85/100). Deposit with GTAW/GMAW/hot-wire, stringer beads, low heat input, interpass typically ≤150 °C and clean surfaces to avoid ductility-dip and hot cracking.
What surface finishes work on ERNiCrFe-11-SA?
Pickle/passivate or lightly grind and buff; no anodizing, and grinding debris must be kept ferrite-free in nuclear service.
Can ERNiCrFe-11-SA be formed, bent or molded?
Supplied as drawn spooled wire or cut lengths; the alloy is ductile enough for wire drawing but is not a wrought structural product form.
What is the maximum service temperature of ERNiCrFe-11-SA?
ERNiCrFe-11-SA is rated for continuous use to about 1,000°C (1,832 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between ERNiCrFe-11-AW and ERNiCrFe-11-SA?
AW is the default condition — standard condition for GTAW/GMAW deposits and overlays used in nuclear DMW joints; no PWHT applied to the nickel weld metal. SA: applied to weld overlays or clad components that receive a full solution anneal with the base metal; homogenises the dendritic structure and lowers strength. Yield strength is 420 MPa in AW versus 330 MPa in SA.
Sources
- AWS A5.14/A5.14M — Nickel and Nickel-Alloy Bare Welding Electrodes and Rods — AWS (2018)
- AWS A5.11/A5.11M — Nickel and Nickel-Alloy Covered Welding Electrodes (ENiCrFe-7) — AWS (2018)
- INCONEL alloy 690 / INCONEL Filler Metal 52-152 product data — Special Metals Corporation (2020)
- ASM Handbook Vol. 6 — Welding, Brazing and Soldering (Ni-alloy filler metals) — ASM International (1993)
- EPRI dissimilar-metal weld and PWSCC mitigation reports — EPRI (2015)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.