Aluminum 2A12
GB 2A12
2A12 (LY12) is a high-strength Al-Cu-Mg 2000-series alloy corresponding closely to 2024, stocked as plate and sheet in O, T3, T4, T351, T42, T6, T62, T81, T851 and H112.
Reference datasheet — 2A12 is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the T4 condition
2A12 tempers and conditions
2A12 is supplied in 10 conditions, soft to hard. T4 is the default FabDigit quotes; the values on this page are for it.
Compare all 10 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Annealed | Choose for deep forming, bending or cold heading before solution treatment. | 75 | 185 | 20 | 47 HB | 50 % IACS |
Strain hardened from hot working only | Low-cost mill-finish bar or profile for non-critical parts that will be heat treated or lightly loaded. | 150 | 260 | 12 | 70 HB | 42 % IACS |
Solution treated by the user and naturally aged | Used when O-temper material is formed first and then heat treated by the fabricator. | 260 | 425 | 19 | 105 HB | 30 % IACS |
T4Default Solution heat treated and naturally aged | Default stocked condition for 2A12 plate, bar and extrusion — best mix of strength, toughness and residual formability. | 325 | 470 | 19 | 120 HB | 30 % IACS |
T3, stress relieved by stretching | Preferred for thick plate that will be heavily machined — low residual stress means minimal distortion. | 325 | 470 | 19 | 120 HB | 30 % IACS |
Solution heat treated, cold worked and naturally aged | Standard aerospace sheet condition where the extra cold work raises yield strength. | 345 | 485 | 18 | 120 HB | 30 % IACS |
T6, heat treated by the user | Same target properties as T6 but achieved by re-heat-treating O or T-temper stock after forming. | 390 | 470 | 9 | 125 HB | 38 % IACS |
Solution heat treated and artificially aged | Pick when a higher yield strength and better stress-corrosion behaviour than T4 are needed, at the cost of ductility. | 395 | 475 | 10 | 125 HB | 38 % IACS |
Solution treated, cold worked, artificially aged | High-yield sheet condition for skins and fittings that must resist creep/exfoliation better than T3. | 450 | 485 | 6 | 128 HB | 38 % IACS |
T8, stress relieved by stretching | Best choice for machined structural plate needing high yield strength, low residual stress and improved exfoliation resistance. | 450 | 480 | 6 | 128 HB | 38 % IACS |
What is 2A12?
2A12 (LY12) is a high-strength Al-Cu-Mg 2000-series alloy corresponding closely to 2024, stocked as plate and sheet in O, T3, T4, T351, T42, T6, T62, T81, T851 and H112. It is used for aerospace tooling, jig plate and precision fixtures because it reaches 470 MPa tensile, 325 MPa yield, 19% elongation and 120 HB while machining cleanly at a rating of 72. Corrosion resistance is poor (rated 30) so cladding, conversion coating or paint is required, fusion welding is not recommended and service is limited to 120 °C; 7075 is the alternative for higher strength, 6061 where welding is needed. 2A12 has a density of 2.78 g/cm³ (0.1 lb/in³), heavier than 74% of aluminum grades. It melts at 502°C (936 °F). 2A12 has a yield strength of 325 MPa (47.1 ksi) and a tensile strength of 470 MPa (68.2 ksi) — stronger than 81% of aluminum grades. Elongation at break is 19% and the elastic modulus is 73 GPa (10.6 Msi).
What is 2A12 used for?
- aerospace tooling
- precision fixtures
- check gauges
- jig plates
Advantages
- Tough — resists crack growth — 37 MPa·√m (33.7 ksi·√in), better than 94% of aluminum grades
- Ductile — tolerates forming and impact — 19%, better than 87% of aluminum grades
- High strength — 325 MPa (47.1 ksi), better than 81% of aluminum grades
- Easy to machine — 72/100, better than 80% of aluminum grades
Limitations
- Needs corrosion protection — 30/100, worse than 98% of aluminum grades
- Difficult to weld — 15/100, worse than 96% of aluminum grades
- Limited service temperature — 120°C (248 °F), worse than 79% of aluminum grades
- Poor heat conductor — 121 W/m·K (69.9 BTU/hr·ft·°F), worse than 76% of aluminum grades
2A12 properties
Typical room-temperature values for 2A12-T4; bars are the position among aluminum grades.
Physical3
2A12 has a density of 2.78 g/cm³ (0.1 lb/in³), heavier than 74% of aluminum grades. It melts at 502°C (936 °F).
Mechanical15
2A12 has a yield strength of 325 MPa (47.1 ksi) and a tensile strength of 470 MPa (68.2 ksi) — stronger than 81% of aluminum grades. Elongation at break is 19% and the elastic modulus is 73 GPa (10.6 Msi).
Thermal6
2A12 is rated for continuous service to 120°C (248 °F). It conducts heat at 121 W/m·K (69.9 BTU/hr·ft·°F), worse than 76% of aluminum grades. Thermal expansion is 23.2 µm/m·K (12.9 µin/in·°F).
Electrical3
2A12 conducts electricity at 30 % IACS, worse than 73% of aluminum grades.
Chemical & Environmental3
Corrosion resistance is poor (30/100), worse than 98% of aluminum grades.
Sustainability4
Producing a kilogram of 2A12 takes about 210 MJ of energy and emits 13.5 kg of CO₂ — more than 88% of aluminum grades. Typical recycled content is 15%.
Manufacturability8
2A12's machinability is very good (72/100, better than 80% of aluminum grades); weldability poor (15/100); formability fair (45/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the aluminum family
Yield strength against density for every aluminum grade FabDigit runs. 2A12 is highlighted; hover a dot for its name, or open the interactive family chart.
Working with 2A12
Is 2A12 easy to machine?
Machines very well in T4/T351/T851 with sharp carbide tools, high speed and flood coolant; chips are short and surface finish is good, but annealed O temper is gummy.
Can 2A12 be welded?
Not recommended for MIG/TIG fusion welding (hot cracking and severe HAZ strength loss); join by riveting, bolting, adhesive bonding or friction-stir welding.
Can 2A12 be formed, bent or molded?
Form in O or freshly quenched (W) temper and re-age; T3/T4 sheet tolerates moderate bends at large radii, artificially aged tempers are nearly unformable.
2A12 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Cuprimary strengthening element | 3.8 – 4.9 | 4.4 |
| Mg | 1.2 – 1.8 | 1.5 |
| Mn | 0.3 – 0.9 | 0.6 |
| Siimpurity | ≤ 0.5 | |
| Feimpurity | ≤ 0.5 | |
| Zn | ≤ 0.3 | |
| Ni | ≤ 0.1 | |
| Ti | ≤ 0.15 | |
| others (each)total ≤ 0.15 | ≤ 0.05 | |
| Al | balance |
What surface finishes work on 2A12?
Chromic or sulfuric anodize plus primer is normal; expect a yellow-brown film, and use clad sheet, Alodine conversion coating or paint for corrosion protection.
Surface treatments FabDigit runs on aluminum parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Organic Coating
Equivalent designations
Standards and trade names that resolve to Aluminum 2A12 in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- GB (China)
- LY12
- Other
- 2024
How much does 2A12 cost?
2A12 is a premium-cost aluminum ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
2A12 — frequently asked
What is 2A12 used for?
2A12 is typically used for aerospace tooling, precision fixtures, check gauges and jig plates. In short: 2024-equivalent tooling plate; high strength, low corrosion resistance; not fusion weldable.
What is the yield strength of 2A12?
2A12 has a typical yield strength of 325 MPa (47.1 ksi) and a tensile strength of 470 MPa (68.2 ksi) — stronger than 81% of aluminum grades. Strength varies by condition: see the 10 listed tempers.
Is 2A12 easy to machine?
Yes — machinability is rated very good (72/100, better than 80% of aluminum grades). Machines very well in T4/T351/T851 with sharp carbide tools, high speed and flood coolant; chips are short and surface finish is good, but annealed O temper is gummy.
Can 2A12 be welded?
Not readily — weldability is rated poor (15/100). Not recommended for MIG/TIG fusion welding (hot cracking and severe HAZ strength loss); join by riveting, bolting, adhesive bonding or friction-stir welding.
What surface finishes work on 2A12?
Chromic or sulfuric anodize plus primer is normal; expect a yellow-brown film, and use clad sheet, Alodine conversion coating or paint for corrosion protection.
Can 2A12 be formed, bent or molded?
Form in O or freshly quenched (W) temper and re-age; T3/T4 sheet tolerates moderate bends at large radii, artificially aged tempers are nearly unformable.
What is the maximum service temperature of 2A12?
2A12 is rated for continuous use to about 120°C (248 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between 2A12-T4 and 2A12-O?
T4 is the default condition — default stocked condition for 2A12 plate, bar and extrusion — best mix of strength, toughness and residual formability. O: choose for deep forming, bending or cold heading before solution treatment. Yield strength is 325 MPa in T4 versus 75 MPa in O.
How much does 2A12 cost?
2A12 is a premium-cost aluminum ($$$), cheaper than about 51% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- ASM Handbook Vol.2: Properties and Selection — Nonferrous Alloys (2024 alloy data) — ASM International (1990)
- MMPDS-17 typical/design properties for 2024 — Battelle/FAA (2022)
- Aluminum Association Teal Sheets — International Alloy Designations — The Aluminum Association (2018)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.