Rigid 10K
also Glass-Filled Resin, SLA High Strength
Rigid Resin is a short-fibre or milled-glass reinforced SLA/DLP/LCD photopolymer available as Glass Filled, Rigid 4000, Rigid 10K, unfilled, High Temp, FR V-0 and ESD grades.
Values for the Glass Filled condition
Rigid 10K grades and fills
Rigid 10K is supplied in 9 conditions, soft to hard. Glass Filled is the default FabDigit quotes; the values on this page are for it.
Compare all 9 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
As-printed, not post-cured | Only for fit checks and visual mock-ups; strength, stiffness and heat resistance are far below datasheet values and creep is severe. | 33 | 40 | 6 | 75 Shore D |
Static-dissipative rigid photopolymer | Use for electronics assembly jigs, trays and nests where surface resistivity must sit in the dissipative window. | — | 50 | 4 | — |
high heat-deflection rigid photopolymer | Choose for hot-air/hot-fluid rigs, mould and lost-wax patterns needing HDT well above 200 °C, accepting very low ductility. | — | 52 | 1.4 | 87 Shore D |
Flame-retardant glass-filled rigid resin | Specify for aerospace-interior, rail and electrical enclosures where UL 94 V-0 at 3 mm is mandatory. | — | 55 | 2 | — |
standard (non-filled) rigid photopolymer | Use for general prototypes and visual models where high stiffness is not required and better ductility/surface finish matters. | — | 65 | 6.2 | 80 Shore D |
~4 GPa glass-filled rigid resin | Pick when you need stiffness plus a little more toughness than the 10 GPa grade — jigs, fixtures, snap-in housings. | — | 69 | 5 | 84 Shore D |
washed and UV/thermally post-cured (property-reference state) | The state all datasheet values refer to: IPA wash, dry, then UV + heat post-cure per producer schedule. | 70 | 75 | 2.5 | 85 Shore D |
Glass FilledDefault glass-reinforced rigid photopolymer, post-cured | Default choice for stiff, dimensionally stable printed parts: thin walls, jigs, housings and fluid-flow models. | — | 75 | 2.5 | 85 Shore D |
Highly glass-filled, 10 GPa modulus | Highest stiffness and heat resistance in the family — thin-wall turbines, ducting, mould inserts and short-run injection tooling. | — | 82 | 1 | 88 Shore D |
What is Rigid 10K?
Rigid Resin is a short-fibre or milled-glass reinforced SLA/DLP/LCD photopolymer available as Glass Filled, Rigid 4000, Rigid 10K, unfilled, High Temp, FR V-0 and ESD grades. The filler raises stiffness and dimensional stability for structural, load-bearing prototypes and fixtures: density 1.55 g/cm3, 75 MPa tensile strength, 5.5 GPa modulus, 85 Shore D and service to 100 °C. Elongation is only 2.5 %, so parts are brittle and notch-sensitive, the glass filler is abrasive (machinability score 40), and properties depend on the post-cure schedule. Tough Resin is the alternative where impact and elongation matter more than stiffness. Rigid 10K has a density of 1.55 g/cm³ (0.056 lb/in³), heavier than 91% of polymer grades. Its glass-transition temperature is 105°C (221 °F). Rigid 10K has a tensile strength of 75 MPa (10.9 ksi), stronger than 80% of polymer grades. Elongation at break is 2.5% and the elastic modulus is 5.5 GPa (0.798 Msi).
What is Rigid 10K used for?
- Engineering prototypes with thin walls
- Jigs and locating fixtures
- Brackets and mounting plates
- Low-volume mould and tooling inserts
- Ducting and manifold prototypes
- Heat-exposed under-hood test parts
- Flame-retardant electronics housings
- ESD-safe handling trays
Advantages
- Stiff — 5.5 GPa (0.798 Msi), better than 88% of polymer grades
- Conducts heat well — 0.3 W/m·K (0.173 BTU/hr·ft·°F), better than 83% of polymer grades
Limitations
- Limited formability — 3/100, worse than 99% of polymer grades
- Difficult to weld — 3/100, worse than 95% of polymer grades
- Heavy — 1.55 g/cm³ (0.056 lb/in³), worse than 91% of polymer grades
- Low fracture toughness — 0.9 MPa·√m (0.819 ksi·√in), worse than 90% of polymer grades
- Limited ductility — 2.5%, worse than 89% of polymer grades
Rigid 10K properties
Typical room-temperature values for Rigid 10K-Glass Filled; bars are the position among polymer grades.
Physical3
Rigid 10K has a density of 1.55 g/cm³ (0.056 lb/in³), heavier than 91% of polymer grades. Its glass-transition temperature is 105°C (221 °F).
Mechanical12
Rigid 10K has a tensile strength of 75 MPa (10.9 ksi), stronger than 80% of polymer grades. Elongation at break is 2.5% and the elastic modulus is 5.5 GPa (0.798 Msi).
Thermal10
Rigid 10K is rated for continuous service to 100°C (212 °F). It conducts heat at 0.3 W/m·K (0.173 BTU/hr·ft·°F), better than 83% of polymer grades. Thermal expansion is 45 µm/m·K (25 µin/in·°F).
Electrical6
Rigid 10K is an electrical insulator with a dielectric strength of 15 kV/mm (381 V/mil) and a resistivity of 1×10¹² Ω·m.
Chemical & Environmental3
Corrosion resistance is very good (80/100), worse than 52% of polymer grades. UV resistance is poor.
Sustainability4
Producing a kilogram of Rigid 10K takes about 115 MJ of energy and emits 6 kg of CO₂ — more than 70% of polymer grades. Typical recycled content is 0%.
Manufacturability4
Rigid 10K's machinability is fair (40/100, worse than 82% of polymer grades); weldability not recommended (3/100); formability not recommended (3/100).
Common Calculations4
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the polymer family
Yield strength against density for every polymer grade FabDigit runs. Rigid 10K is highlighted; hover a dot for its name, or open the interactive family chart.
Working with Rigid 10K
Is Rigid 10K easy to machine?
Drilling, tapping and light milling are possible but the part is brittle and the glass filler is abrasive — use sharp carbide tools, low feed, no coolant soak, and extract the dust (respirator required).
Can Rigid 10K be welded?
Thermoset: cannot be welded or reflowed; join with cyanoacrylate, two-part epoxy or UV-cure adhesive, and screw into heat-set/threaded inserts rather than tapped resin.
Can Rigid 10K be formed, bent or molded?
Printed on SLA/DLP/LCD at 385–405 nm with a heated (30–35 °C) tank; shake/stir the cartridge because glass filler settles, then IPA wash 5–10 min, dry, and post-cure under UV at 60–80 °C per producer schedule to reach datasheet properties.
Manufacturability
The process limits FabDigit's quote engine applies to Rigid 10K. Design inside these and the part quotes instantly; outside them it routes to an engineer.
Injection molding
| Mold shrinkage | — |
|---|---|
| Wall thickness | — – — |
| Recommended draft | — |
| Pre-drying | — |
3D printing
| Technologies | SLA |
|---|---|
| Layer height | 50 – 300 µmdefault 100 µm |
| Minimum wall / feature | 1 / 0.5 mm |
| Build envelope | 300 × 300 × 380 mm |
| Supports | Yes |
| Anisotropy | Moderate |
Rigid 10K chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| acrylate/methacrylate reactive diluent mcontrols viscosity and cure shrinkage | 10 – 40 | 22 |
| glass fiber / glass microspheressilane-treated; ~15–25% in Rigid 4000-class, ~40–50% in Rigid 10K-class | 10 – 55 | 35 |
| photoinitiator (acylphosphine oxide type385/405 nm absorption | 0.5 – 3 | 1.5 |
| pigment, UV blocker, stabilizer, disperscontrols cure depth and shelf life | 0.2 – 3 | 1 |
| urethane/epoxy acrylate–methacrylate olicrosslinking backbone; exact chemistry proprietary | ≥ 25 (balance) | — |
What surface finishes work on Rigid 10K?
Sands and primes well; bead-blast or 400–800 grit for a uniform matte, then use a UV-blocking primer/topcoat since bare photopolymer yellows and embrittles outdoors — electroplating requires a conductive base coat.
Surface treatments FabDigit runs on polymer parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Coating
Injection Molding Coating
Metallization / Functional
Coloring
Equivalent designations
Standards and trade names that resolve to Rigid 10K in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- Trade names
- Glass-Filled ResinSLA High StrengthGlass-Filled / Fiber Resin
How much does Rigid 10K cost?
Rigid 10K is a premium-cost polymer ($$$), cheaper than about 71% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Rigid 10K — frequently asked
What is Rigid 10K used for?
Rigid 10K is typically used for engineering prototypes with thin walls, jigs and locating fixtures, brackets and mounting plates, low-volume mould and tooling inserts, ducting and manifold prototypes and heat-exposed under-hood test parts. In short: stiff glass-filled resin.
What is the tensile strength of Rigid 10K?
Rigid 10K has a typical tensile strength of 75 MPa (10.9 ksi) — stronger than 80% of polymer grades. Strength varies by condition: see the 9 listed tempers.
Is Rigid 10K easy to machine?
Not especially — machinability is rated fair (40/100, worse than 82% of polymer grades). Drilling, tapping and light milling are possible but the part is brittle and the glass filler is abrasive — use sharp carbide tools, low feed, no coolant soak, and extract the dust (respirator required).
Can Rigid 10K be welded?
Not readily — weldability is rated not recommended (3/100). Thermoset: cannot be welded or reflowed; join with cyanoacrylate, two-part epoxy or UV-cure adhesive, and screw into heat-set/threaded inserts rather than tapped resin.
What surface finishes work on Rigid 10K?
Sands and primes well; bead-blast or 400–800 grit for a uniform matte, then use a UV-blocking primer/topcoat since bare photopolymer yellows and embrittles outdoors — electroplating requires a conductive base coat.
Can Rigid 10K be formed, bent or molded?
Printed on SLA/DLP/LCD at 385–405 nm with a heated (30–35 °C) tank; shake/stir the cartridge because glass filler settles, then IPA wash 5–10 min, dry, and post-cure under UV at 60–80 °C per producer schedule to reach datasheet properties.
What is the maximum service temperature of Rigid 10K?
Rigid 10K is rated for continuous use to about 100°C (212 °F), and briefly to 150°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between Rigid 10K Glass Filled and Rigid 10K GREEN?
Glass Filled is the default condition — default choice for stiff, dimensionally stable printed parts: thin walls, jigs, housings and fluid-flow models. GREEN: only for fit checks and visual mock-ups; strength, stiffness and heat resistance are far below datasheet values and creep is severe.
How much does Rigid 10K cost?
Rigid 10K is a premium-cost polymer ($$$), cheaper than about 71% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Can FabDigit make parts in Rigid 10K?
Yes — Rigid 10K is available for injection molding and 3D printing with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- Rigid 10K Resin — Technical Data Sheet — Formlabs (2023)
- Rigid 4000 Resin — Technical Data Sheet — Formlabs (2023)
- High Temp Resin V2 / Flame Retardant Resin / ESD Resin data sheets — Formlabs (2023)
- Loctite 3D IND & MED photopolymer resin data sheets — Henkel (2022)
- ASTM D638 / D790 / D256 / D648 / D570 test methods — ASTM International (2022)
- UL 94 Standard for Tests for Flammability of Plastic Materials — UL Solutions (2021)
- Engineering Plastics (Engineered Materials Handbook Vol. 2) — thermoset acrylates — ASM International (1988)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.