VeroBlackPlus
also RGD875
VeroBlackPlus (RGD875) is a rigid, opaque black acrylic-based photopolymer for PolyJet material jetting, available in glossy and matte finishes, HQ16 and HS30 print modes and a DM-GREY digital-material blend.
Reference datasheet — VeroBlackPlus is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the GLOSSY condition
VeroBlackPlus grades and fills
VeroBlackPlus is supplied in 4 conditions, soft to hard. GLOSSY is the default FabDigit quotes; the values on this page are for it.
Compare all 4 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
High Speed / Draft mode | Cheapest, fastest build for large massing models where surface detail is not critical. | 47 | 51 | 13 | 83 Shore D |
GLOSSYDefault Printed with support only under overhangs | Default choice for visual models: deepest black, highest gloss and best measured strength. | 50 | 55 | 17 | 84 Shore D |
Digital Material grey shades | Choose when a calibrated grey tone is needed in one build; mechanical properties stay in the rigid-opaque band. | 50 | 55 | 20 | 84 Shore D |
High Quality mode | Use for fine text, thin walls and sharp edges; slower build, slightly better strength consistency. | 53 | 58 | 18 | 85 Shore D |
Supply forms, finishes and certifications
Ways VeroBlackPlus is supplied — form, process route, surface or paperwork — without a datasheet of their own. The property values above apply.
| Option | What it is | Type |
|---|---|---|
MATTE | Part fully encapsulated in support gel, satin surface after cleaning | Surface finish |
What is VeroBlackPlus?
VeroBlackPlus (RGD875) is a rigid, opaque black acrylic-based photopolymer for PolyJet material jetting, available in glossy and matte finishes, HQ16 and HS30 print modes and a DM-GREY digital-material blend. It is chosen for deep black cosmetic prototypes with sharp detail, printed as visual models, housings and fit-check parts, with 55 MPa tensile strength and 17 % elongation. As a UV-cured thermoset it is notch-sensitive, softens near 50 °C and yellows or embrittles under UV, so it suits prototypes rather than functional service parts. VeroGray is the same resin family in a neutral colour. VeroBlackPlus has a density of 1.18 g/cm³ (0.0424 lb/in³), lighter than 52% of polymer grades. Its glass-transition temperature is 53°C (127 °F). VeroBlackPlus has a yield strength of 50 MPa (7.25 ksi) and a tensile strength of 55 MPa (7.98 ksi) — stronger than 52% of polymer grades. Elongation at break is 17% and the elastic modulus is 2.5 GPa (0.363 Msi).
What is VeroBlackPlus used for?
- visual prototypes
- consumer electronics housings
- black cosmetic parts
- assembly fit checks
Advantages
- Polishes to a fine finish — 80/100, better than 89% of polymer grades
Limitations
- Limited service temperature — 45°C (113 °F), worse than 98% of polymer grades
- Limited formability — 5/100, worse than 95% of polymer grades
- Absorbs moisture — dry before molding — 1.3%, worse than 88% of polymer grades
- Difficult to weld — 10/100, worse than 82% of polymer grades
- Needs corrosion protection — 70/100, worse than 78% of polymer grades
VeroBlackPlus properties
Typical room-temperature values for VeroBlackPlus-GLOSSY; bars are the position among polymer grades.
Physical4
VeroBlackPlus has a density of 1.18 g/cm³ (0.0424 lb/in³), lighter than 52% of polymer grades. Its glass-transition temperature is 53°C (127 °F).
Mechanical14
VeroBlackPlus has a yield strength of 50 MPa (7.25 ksi) and a tensile strength of 55 MPa (7.98 ksi) — stronger than 52% of polymer grades. Elongation at break is 17% and the elastic modulus is 2.5 GPa (0.363 Msi).
Thermal11
VeroBlackPlus is rated for continuous service to 45°C (113 °F). It conducts heat at 0.2 W/m·K (0.116 BTU/hr·ft·°F), worse than 56% of polymer grades. Thermal expansion is 80 µm/m·K (44.4 µin/in·°F).
Electrical2
VeroBlackPlus has an electrical resistivity of 1×10¹² Ω·m.
Chemical & Environmental3
Corrosion resistance is very good (70/100), worse than 78% of polymer grades. UV resistance is poor.
Sustainability3
Producing a kilogram of VeroBlackPlus takes about 110 MJ of energy and emits 5.5 kg of CO₂ — more than 64% of polymer grades. Typical recycled content is 0%.
Manufacturability4
VeroBlackPlus's machinability is good (55/100, worse than 64% of polymer grades); weldability not recommended (10/100); formability not recommended (5/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the polymer family
Yield strength against density for every polymer grade FabDigit runs. VeroBlackPlus is highlighted; hover a dot for its name, or open the interactive family chart.
Working with VeroBlackPlus
Is VeroBlackPlus easy to machine?
Drill, tap and sand at low speed with sharp tools and light feed — the cured acrylate is notch-sensitive and softens near 50 °C, so avoid dry high-speed cutting.
Can VeroBlackPlus be welded?
Thermoset, so no thermal welding; bond with cyanoacrylate, UV-cure acrylate or epoxy after light scuffing and degreasing.
Can VeroBlackPlus be formed, bent or molded?
Shape is defined entirely by the print — no post-forming; orient thin features to build direction, allow ~0.1 mm/100 mm growth and design ≥0.6 mm walls, then water-jet or NaOH-soak the SUP support gel away.
VeroBlackPlus chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| acrylate monomers (isobornyl acrylate / reactive diluents controlling viscosity and Tg | 40 – 70 | 55 |
| acrylic monomer, multifunctional (crossl | 5 – 15 | 8 |
| photoinitiator (acylphosphine oxide type | 1 – 3 | 2 |
| carbon black pigmentgives opaque deep black; also raises UV absorption | 0.5 – 2 | 1 |
| stabilizers / surfactants | 0.1 – 1 | 0.5 |
| urethane/epoxy acrylate oligomersnetwork former | ≥ 20 (balance) |
What surface finishes work on VeroBlackPlus?
Sands from 400 to 2000 grit and takes primer, solvent-free paint and clear lacquer well; the as-printed glossy black polishes to near-piano finish but UV clear-coat is recommended to slow yellowing/embrittlement.
Equivalent designations
Standards and trade names that resolve to VeroBlackPlus in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- Trade names
- RGD875
How much does VeroBlackPlus cost?
VeroBlackPlus is a high-cost polymer ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
VeroBlackPlus — frequently asked
What is VeroBlackPlus used for?
VeroBlackPlus is typically used for visual prototypes, consumer electronics housings, black cosmetic parts and assembly fit checks. In short: deep black PolyJet resin; sharp cosmetic detail; prototype use, not functional.
What is the yield strength of VeroBlackPlus?
VeroBlackPlus has a typical yield strength of 50 MPa (7.25 ksi) and a tensile strength of 55 MPa (7.98 ksi) — stronger than 52% of polymer grades. Strength varies by condition: see the 4 listed tempers.
Is VeroBlackPlus easy to machine?
Reasonably — machinability is rated good (55/100, worse than 64% of polymer grades). Drill, tap and sand at low speed with sharp tools and light feed — the cured acrylate is notch-sensitive and softens near 50 °C, so avoid dry high-speed cutting.
Can VeroBlackPlus be welded?
Not readily — weldability is rated not recommended (10/100). Thermoset, so no thermal welding; bond with cyanoacrylate, UV-cure acrylate or epoxy after light scuffing and degreasing.
What surface finishes work on VeroBlackPlus?
Sands from 400 to 2000 grit and takes primer, solvent-free paint and clear lacquer well; the as-printed glossy black polishes to near-piano finish but UV clear-coat is recommended to slow yellowing/embrittlement.
Can VeroBlackPlus be formed, bent or molded?
Shape is defined entirely by the print — no post-forming; orient thin features to build direction, allow ~0.1 mm/100 mm growth and design ≥0.6 mm walls, then water-jet or NaOH-soak the SUP support gel away.
What is the maximum service temperature of VeroBlackPlus?
VeroBlackPlus is rated for continuous use to about 45°C (113 °F), and briefly to 60°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between VeroBlackPlus GLOSSY and VeroBlackPlus HQ16?
GLOSSY is the default condition — default choice for visual models: deepest black, highest gloss and best measured strength. HQ16: use for fine text, thin walls and sharp edges; slower build, slightly better strength consistency. Yield strength is 50 MPa in GLOSSY versus 53 MPa in HQ16.
How much does VeroBlackPlus cost?
VeroBlackPlus is a high-cost polymer ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- PolyJet Rigid Opaque Materials (Vero family, RGD8xx) data sheet — Stratasys (2023)
- PolyJet Materials Safety and Handling / Digital Materials guide — Stratasys (2022)
- ASTM D638 / D790 / D256 / D648 / D785 / D570 test methods — ASTM International (2022)
- Material-jetting photopolymer property compilations — CAMPUS / Senvol-style AM material databases (2024)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.