VeroBlackPlus HS30
Print state
also RGD875
HS30 = high Speed / Draft mode
Cheapest, fastest build for large massing models where surface detail is not critical.
Values for the HS30 condition
Other VeroBlackPlus grades and fills
VeroBlackPlus is listed in 4 conditions; see the grade overview at VeroBlackPlus.
Compare all 4 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
HS30This page High Speed / Draft mode | Cheapest, fastest build for large massing models where surface detail is not critical. | 47 | 51 | 13 | 83 Shore D |
GLOSSYDefault Printed with support only under overhangs | Default choice for visual models: deepest black, highest gloss and best measured strength. | 50 | 55 | 17 | 84 Shore D |
Digital Material grey shades | Choose when a calibrated grey tone is needed in one build; mechanical properties stay in the rigid-opaque band. | 50 | 55 | 20 | 84 Shore D |
High Quality mode | Use for fine text, thin walls and sharp edges; slower build, slightly better strength consistency. | 53 | 58 | 18 | 85 Shore D |
What is VeroBlackPlus HS30?
VeroBlackPlus HS30 is VeroBlackPlus in the HS30 condition — cheapest, fastest build for large massing models where surface detail is not critical. VeroBlackPlus HS30 has a yield strength of 47 MPa (6.82 ksi) and a tensile strength of 51 MPa (7.4 ksi) — weaker than 55% of polymer grades. Elongation at break is 13% and the elastic modulus is 2.4 GPa (0.348 Msi). VeroBlackPlus HS30 has a density of 1.18 g/cm³ (0.0424 lb/in³), lighter than 52% of polymer grades. Its glass-transition temperature is 53°C (127 °F). GLOSSY is the default condition FabDigit quotes; HS30 is available on request or by drawing note.
Advantages
- Polishes to a fine finish — 80/100, better than 89% of polymer grades
Limitations
- Limited service temperature — 45°C (113 °F), worse than 98% of polymer grades
- Limited formability — 5/100, worse than 95% of polymer grades
- Absorbs moisture — dry before molding — 1.3%, worse than 88% of polymer grades
- Difficult to weld — 10/100, worse than 82% of polymer grades
- Needs corrosion protection — 70/100, worse than 78% of polymer grades
VeroBlackPlus HS30 properties
Typical room-temperature values for VeroBlackPlus HS30; 24 are specific to this condition. Other listed values are VeroBlackPlus reference data and may not represent this condition. Bars are the position among polymer grades.
Physical4
VeroBlackPlus HS30 has a density of 1.18 g/cm³ (0.0424 lb/in³), lighter than 52% of polymer grades. Its glass-transition temperature is 53°C (127 °F).
Mechanical14
VeroBlackPlus HS30 has a yield strength of 47 MPa (6.82 ksi) and a tensile strength of 51 MPa (7.4 ksi) — weaker than 55% of polymer grades. Elongation at break is 13% and the elastic modulus is 2.4 GPa (0.348 Msi).
Thermal11
VeroBlackPlus HS30 is rated for continuous service to 45°C (113 °F). It conducts heat at 0.2 W/m·K (0.116 BTU/hr·ft·°F), worse than 56% of polymer grades. Thermal expansion is 80 µm/m·K (44.4 µin/in·°F).
Electrical2
VeroBlackPlus HS30 has an electrical resistivity of 1×10¹² Ω·m.
Chemical & Environmental3
Corrosion resistance is very good (70/100), worse than 78% of polymer grades. UV resistance is poor.
Sustainability3
Producing a kilogram of VeroBlackPlus HS30 takes about 110 MJ of energy and emits 5.5 kg of CO₂ — more than 64% of polymer grades. Typical recycled content is 0%.
Manufacturability4
VeroBlackPlus HS30's machinability is good (55/100, worse than 64% of polymer grades); weldability not recommended (10/100); formability not recommended (5/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with VeroBlackPlus HS30
Is VeroBlackPlus easy to machine?
Drill, tap and sand at low speed with sharp tools and light feed — the cured acrylate is notch-sensitive and softens near 50 °C, so avoid dry high-speed cutting.
Can VeroBlackPlus be welded?
Thermoset, so no thermal welding; bond with cyanoacrylate, UV-cure acrylate or epoxy after light scuffing and degreasing.
Can VeroBlackPlus be formed, bent or molded?
Shape is defined entirely by the print — no post-forming; orient thin features to build direction, allow ~0.1 mm/100 mm growth and design ≥0.6 mm walls, then water-jet or NaOH-soak the SUP support gel away.
What surface finishes work on VeroBlackPlus?
Sands from 400 to 2000 grit and takes primer, solvent-free paint and clear lacquer well; the as-printed glossy black polishes to near-piano finish but UV clear-coat is recommended to slow yellowing/embrittlement.
VeroBlackPlus chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| acrylate monomers (isobornyl acrylate / reactive diluents controlling viscosity and Tg | 40 – 70 | 55 |
| acrylic monomer, multifunctional (crossl | 5 – 15 | 8 |
| photoinitiator (acylphosphine oxide type | 1 – 3 | 2 |
| carbon black pigmentgives opaque deep black; also raises UV absorption | 0.5 – 2 | 1 |
| stabilizers / surfactants | 0.1 – 1 | 0.5 |
| urethane/epoxy acrylate oligomersnetwork former | ≥ 20 (balance) | — |
VeroBlackPlus HS30 — frequently asked
What is VeroBlackPlus HS30 used for?
VeroBlackPlus HS30 is typically used for visual prototypes, consumer electronics housings, black cosmetic parts and assembly fit checks. In short: deep black PolyJet resin; sharp cosmetic detail; prototype use, not functional.
What is the yield strength of VeroBlackPlus HS30?
VeroBlackPlus HS30 has a typical yield strength of 47 MPa (6.82 ksi) and a tensile strength of 51 MPa (7.4 ksi) — weaker than 55% of polymer grades. Strength varies by condition: see the 4 listed tempers.
Is VeroBlackPlus HS30 easy to machine?
Reasonably — machinability is rated good (55/100, worse than 64% of polymer grades). Drill, tap and sand at low speed with sharp tools and light feed — the cured acrylate is notch-sensitive and softens near 50 °C, so avoid dry high-speed cutting.
Can VeroBlackPlus HS30 be welded?
Not readily — weldability is rated not recommended (10/100). Thermoset, so no thermal welding; bond with cyanoacrylate, UV-cure acrylate or epoxy after light scuffing and degreasing.
What surface finishes work on VeroBlackPlus HS30?
Sands from 400 to 2000 grit and takes primer, solvent-free paint and clear lacquer well; the as-printed glossy black polishes to near-piano finish but UV clear-coat is recommended to slow yellowing/embrittlement.
Can VeroBlackPlus HS30 be formed, bent or molded?
Shape is defined entirely by the print — no post-forming; orient thin features to build direction, allow ~0.1 mm/100 mm growth and design ≥0.6 mm walls, then water-jet or NaOH-soak the SUP support gel away.
What is the maximum service temperature of VeroBlackPlus HS30?
VeroBlackPlus HS30 is rated for continuous use to about 45°C (113 °F), and briefly to 60°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between VeroBlackPlus GLOSSY and VeroBlackPlus HQ16?
GLOSSY is the default condition — default choice for visual models: deepest black, highest gloss and best measured strength. HQ16: use for fine text, thin walls and sharp edges; slower build, slightly better strength consistency. Yield strength is 50 MPa in GLOSSY versus 53 MPa in HQ16.
Sources
- PolyJet Rigid Opaque Materials (Vero family, RGD8xx) data sheet — Stratasys (2023)
- PolyJet Materials Safety and Handling / Digital Materials guide — Stratasys (2022)
- ASTM D638 / D790 / D256 / D648 / D785 / D570 test methods — ASTM International (2022)
- Material-jetting photopolymer property compilations — CAMPUS / Senvol-style AM material databases (2024)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.