Digital ABS Plus vs VeroBlackPlus
Polymer · grade comparison
Digital ABS Plus and VeroBlackPlus are both polymer grades. Digital ABS Plus is the more ductile: elongation 30% versus 17% for VeroBlackPlus. Digital ABS Plus is stiffer (2.8 GPa vs 2.5 GPa) and Digital ABS Plus runs hotter in service (50°C vs 45°C continuous).
Digital ABS PlusChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Digital ABS Plus vs VeroBlackPlus: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Shore D
Hardness, Rockwell M
Yield Strength (0.2% offset)
Shear Strength
Fracture Toughness (K_IC)
Hardness, Rockwell R
Same in both: Compressive Strength 80 MPa11.6 ksi
Physical
Density and transition temperatures.
Glass Transition (Tg)
Water Absorption (24 h)
Water Absorption (Saturation)
Same in both: Density 1.18 g/cm³0.04 lb/in³
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Vicat Softening Point (B50)
Limiting Oxygen Index
Max Service Temperature (short-term)
Same in both: Thermal Conductivity 0.2 W/m·K0.12 BTU/hr·ft·°F · Specific Heat Capacity 1,500 J/kg·K0.36 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 80 µm/m·K44.4 µin/in·°F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Strength
Dielectric Constant (1 MHz)
Volume Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Polishability
Mold Shrinkage
Formability (cold)
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Same in both: Typical Recycled Content 0%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Diffusivity 0.1 mm²/s · Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Digital ABS Plus | VeroBlackPlus |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Digital ABS Plus vs VeroBlackPlus — frequently asked
What is the difference between Digital ABS Plus and VeroBlackPlus?
Digital ABS Plus and VeroBlackPlus are both polymer grades. Digital ABS Plus is the more ductile: elongation 30% versus 17% for VeroBlackPlus. Digital ABS Plus is stiffer (2.8 GPa vs 2.5 GPa) and Digital ABS Plus runs hotter in service (50°C vs 45°C continuous).
Which is cheaper, Digital ABS Plus or VeroBlackPlus?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, Digital ABS Plus or VeroBlackPlus?
Digital ABS Plus, by a small margin. Both rate good for machinability — 60/100 against 55/100 for VeroBlackPlus; for welding the order is VeroBlackPlus first (not recommended, 10/100) then Digital ABS Plus (not recommended, 5/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Digital ABS Plus and VeroBlackPlus side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.