Stainless Steel S32202 As Welded
Finish state
UNS S32202 · EN 1.4062
Represents fabricated joints made with matching or 2209/2307-type filler under controlled heat input; expect somewhat lower toughness and local corrosion performance.
Values for the As Welded condition
Other S32202 tempers and conditions
S32202 is listed in 3 conditions; see the grade overview at S32202.
Compare all 3 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
AnnealedDefault solution annealed and pickled (2B cold-rolled sheet/coil, ~1000–1050 °C water quench) | Standard stocked condition for sheet, coil and strip; best combination of strength, ductility and corrosion resistance. | 520 | 750 | 35 | 23 HRC | — |
As WeldedThis page weld metal / HAZ, no post-weld solution anneal | Represents fabricated joints made with matching or 2209/2307-type filler under controlled heat input; expect somewhat lower toughness and local corrosion performance. | 520 | 740 | 25 | 25 HRC | 2.2 % IACS |
Cold drawn | Pick when tighter tolerances, straightness and higher yield strength are needed; ductility and formability drop. | 680 | 850 | 20 | 29 HRC | 2.2 % IACS |
What is S32202 As Welded?
S32202 As Welded is S32202 supplied in the As Welded condition — represents fabricated joints made with matching or 2209/2307-type filler under controlled heat input; expect somewhat lower toughness and local corrosion performance. S32202 As Welded has a yield strength of 520 MPa (75.4 ksi) and a tensile strength of 740 MPa (107 ksi) — stronger than 79% of stainless steel grades. Elongation at break is 25% and the elastic modulus is 200 GPa (29 Msi). S32202 As Welded has a density of 7.7 g/cm³ (0.278 lb/in³), lighter than 83% of stainless steel grades. It melts at 1,420°C (2,588 °F). Annealed is the default condition FabDigit quotes; As Welded is available on request or by drawing note.
Advantages
- High strength — 520 MPa (75.4 ksi), better than 79% of stainless steel grades
Limitations
- Limited service temperature — 280°C (536 °F), worse than 96% of stainless steel grades
- Low fracture toughness — 80 MPa·√m (72.8 ksi·√in), worse than 79% of stainless steel grades
S32202 As Welded properties
Typical room-temperature values for S32202 As Welded; 23 are specific to this condition. Other listed values are S32202 reference data and may not represent this condition. Bars are the position among stainless steel grades.
Physical3
S32202 As Welded has a density of 7.7 g/cm³ (0.278 lb/in³), lighter than 83% of stainless steel grades. It melts at 1,420°C (2,588 °F).
Mechanical17
S32202 As Welded has a yield strength of 520 MPa (75.4 ksi) and a tensile strength of 740 MPa (107 ksi) — stronger than 79% of stainless steel grades. Elongation at break is 25% and the elastic modulus is 200 GPa (29 Msi).
Thermal6
S32202 As Welded is rated for continuous service to 280°C (536 °F). It conducts heat at 15 W/m·K (8.67 BTU/hr·ft·°F), worse than 59% of stainless steel grades. Thermal expansion is 13 µm/m·K (7.22 µin/in·°F).
Electrical3
S32202 As Welded conducts electricity at 2.2 % IACS, worse than 61% of stainless steel grades.
Chemical & Environmental3
Corrosion resistance is good (55/100), worse than 71% of stainless steel grades.
Sustainability4
Producing a kilogram of S32202 As Welded takes about 53 MJ of energy and emits 4.5 kg of CO₂ — less than 67% of stainless steel grades. Typical recycled content is 70%.
Manufacturability7
S32202 As Welded's machinability is poor (30/100, worse than 70% of stainless steel grades); weldability very good (70/100); formability fair (40/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with S32202 As Welded
Is S32202 easy to machine?
Machine like 2205 but with ~20–30% lower cutting speeds than 304: rigid setups, sharp coated carbide, heavy positive feeds to cut under the work-hardened layer, and copious coolant.
Can S32202 be welded?
Weldable by GTAW/GMAW/SMAW/SAW with 2209 or 2307-type filler (autogenous welding only with N₂-bearing shielding plus a re-anneal); keep heat input roughly 0.2–1.5 kJ/mm and interpass below ~150 °C to hold 30–70% ferrite.
Can S32202 be formed, bent or molded?
Cold formable but needs ~2× the press force and larger bend allowances than 304 due to high yield strength and springback; hot form at 950–1150 °C followed by full solution anneal and water quench.
What surface finishes work on S32202?
Pickle and passivate after hot work or welding to restore the passive film; takes standard 2B/BA/No.4 and mirror polishes, and is readily electropolished.
S32202 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Clow carbon to avoid carbide precipitation | ≤ 0.03 | 0.02 |
| Si | ≤ 1 | 0.4 |
| Mnpartial Ni substitute, aids N solubility | ≤ 2 | 1.4 |
| P | ≤ 0.04 | 0.03 |
| S | ≤ 0.01 | 0 |
| Cr | 21.5 – 24 | 22.5 |
| Nilean nickel content keeps cost stable | 1 – 2.8 | 2.2 |
| Momolybdenum-free grade; residual only | ≤ 0.45 | 0.25 |
| Naustenite stabiliser, raises strength and pitting resistance | 0.18 – 0.26 | 0.21 |
| Fe | balance | — |
S32202 As Welded — frequently asked
What is S32202 As Welded used for?
S32202 As Welded is typically used for structural pipe, tanks and architectural panels. In short: molybdenum-free lean duplex; between 2101 and 2304; high strength, moderate corrosion.
What is the yield strength of S32202 As Welded?
S32202 As Welded has a typical yield strength of 520 MPa (75.4 ksi) and a tensile strength of 740 MPa (107 ksi) — stronger than 79% of stainless steel grades. Strength varies by condition: see the 3 listed tempers.
Is S32202 As Welded easy to machine?
Not especially — machinability is rated poor (30/100, worse than 70% of stainless steel grades). Machine like 2205 but with ~20–30% lower cutting speeds than 304: rigid setups, sharp coated carbide, heavy positive feeds to cut under the work-hardened layer, and copious coolant.
Can S32202 As Welded be welded?
Yes — weldability is rated very good (70/100). Weldable by GTAW/GMAW/SMAW/SAW with 2209 or 2307-type filler (autogenous welding only with N₂-bearing shielding plus a re-anneal); keep heat input roughly 0.2–1.5 kJ/mm and interpass below ~150 °C to hold 30–70% ferrite.
What surface finishes work on S32202 As Welded?
Pickle and passivate after hot work or welding to restore the passive film; takes standard 2B/BA/No.4 and mirror polishes, and is readily electropolished.
Can S32202 As Welded be formed, bent or molded?
Cold formable but needs ~2× the press force and larger bend allowances than 304 due to high yield strength and springback; hot form at 950–1150 °C followed by full solution anneal and water quench.
What is the maximum service temperature of S32202 As Welded?
S32202 As Welded is rated for continuous use to about 280°C (536 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between S32202 Annealed and S32202-CD?
Annealed is the default condition — standard stocked condition for sheet, coil and strip; best combination of strength, ductility and corrosion resistance. CD: pick when tighter tolerances, straightness and higher yield strength are needed; ductility and formability drop. Yield strength is 520 MPa in Annealed versus 680 MPa in CD.
Sources
- ASTM A240/A240M — Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip — ASTM International (2023)
- ASTM A789/A790 — Duplex Stainless Steel Tubing and Pipe — ASTM International (2021)
- EN 10088-2/-3 (X2CrNiN22-2, 1.4062) — CEN (2014)
- Outokumpu Forta LDX / 2202 duplex data sheet — Outokumpu (2022)
- UR 2202 lean duplex stainless steel — Industeel / Aperam (2021)
- ASM Handbook Vol.1 — Properties and Selection: Irons, Steels, and High-Performance Alloys — ASM International (1990)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.