Durable Resin GREEN
Print state
also PP-Like Resin, PP-Like / Durable Resin
Reference state only — use for fit checks; strength and stiffness are well below post-cured values and creep is high.
Values for the GREEN condition
Other Durable Resin grades and fills
Durable Resin is listed in 3 conditions; see the grade overview at Durable Resin.
- GREEN
- Tough-1500
- Tough
Compare all 3 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
GREENThis page Green (as-printed, not post-cured) | Reference state only — use for fit checks; strength and stiffness are well below post-cured values and creep is high. | 13 | 18 | 49 | 57 Shore D |
Compliant tough grade | Pick for parts that must flex repeatedly and spring back — clips, cable ties, panels with press-fit features — a stiffness step between PP-like and ABS-like. | — | 33 | 51 | 75 Shore D |
ABS-like tough grade | Pick when the part needs both stiffness and impact resistance — housings, jigs, brackets, threaded/assembled prototypes replacing ABS. | 42 | 46 | 48 | 80 Shore D |
What is Durable Resin GREEN?
Durable Resin GREEN is Durable Resin in the GREEN condition — reference state only — use for fit checks; strength and stiffness are well below post-cured values and creep is high. Durable Resin GREEN has a yield strength of 13 MPa (1.89 ksi) and a tensile strength of 18 MPa (2.61 ksi) — weaker than 86% of polymer grades. Elongation at break is 49% and the elastic modulus is 0.5 GPa (0.0725 Msi). Durable Resin GREEN has a density of 1.12 g/cm³ (0.0405 lb/in³), lighter than 64% of polymer grades. Its glass-transition temperature is 45°C (113 °F).
Limitations
- Limited service temperature — 28°C (82 °F), worse than 100% of polymer grades
- Needs corrosion protection — 60/100, worse than 89% of polymer grades
- Difficult to weld — 5/100, worse than 89% of polymer grades
- Low strength — 13 MPa (1.89 ksi), worse than 86% of polymer grades
- Difficult to machine — 40/100, worse than 82% of polymer grades
Durable Resin GREEN properties
Typical room-temperature values for Durable Resin GREEN; 24 are specific to this condition. Other listed values are Durable Resin reference data and may not represent this condition. Bars are the position among polymer grades.
Physical5
Durable Resin GREEN has a density of 1.12 g/cm³ (0.0405 lb/in³), lighter than 64% of polymer grades. Its glass-transition temperature is 45°C (113 °F).
Mechanical11
Durable Resin GREEN has a yield strength of 13 MPa (1.89 ksi) and a tensile strength of 18 MPa (2.61 ksi) — weaker than 86% of polymer grades. Elongation at break is 49% and the elastic modulus is 0.5 GPa (0.0725 Msi).
Thermal7
Durable Resin GREEN is rated for continuous service to 28°C (82 °F). It conducts heat at 0.19 W/m·K (0.11 BTU/hr·ft·°F), worse than 68% of polymer grades. Thermal expansion is 130 µm/m·K (72.2 µin/in·°F).
Electrical4
Durable Resin GREEN is an electrical insulator with a dielectric strength of 16 kV/mm (406.4 V/mil) and a resistivity of 1×10¹¹ Ω·m.
Chemical & Environmental3
Corrosion resistance is good (60/100), worse than 89% of polymer grades. UV resistance is poor.
Sustainability3
Producing a kilogram of Durable Resin GREEN takes about 130 MJ of energy and emits 5.5 kg of CO₂ — more than 77% of polymer grades. Typical recycled content is 0%.
Manufacturability4
Durable Resin GREEN's machinability is fair (40/100, worse than 82% of polymer grades); weldability not recommended (5/100); formability poor (30/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with Durable Resin GREEN
Is Durable Resin easy to machine?
Machinable with sharp tools, high speed and low feed, but the soft matrix smears — prefer drilling/reaming to milling and avoid coolant soak.
Can Durable Resin be welded?
Thermoset — cannot be heat welded; join with cyanoacrylate, UV-cure acrylate or two-part epoxy after light abrasion.
Can Durable Resin be formed, bent or molded?
Print at 50–100 µm layers, orient living hinges so bending is across layers, then wash briefly in IPA (<10–15 min) and heat post-cure (typically 60–70 °C UV) to reach datasheet properties.
What surface finishes work on Durable Resin?
Sands and vapor-free polishes to a satin finish; primer + flexible paint or dyeing works, but keep parts out of sunlight or clear-coat with a UV-blocking topcoat.
Durable Resin chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| urethane acrylate / aliphatic acrylate oflexible backbone giving the PP-like high elongation | 40 – 70 | 55 |
| photoinitiator (acylphosphine oxide type | 0.5 – 3 | 1.5 |
| pigments, UV blockers, additives | 0.1 – 3 | 1 |
| acrylate & methacrylate reactive monomercontrols viscosity, crosslink density and modulus | ≥ 25 (balance) | — |
Durable Resin GREEN — frequently asked
What is Durable Resin GREEN used for?
Durable Resin GREEN is typically used for living hinges, snap fits and clips, PP-like functional prototypes, low-friction wear pads and bushing prototypes, press-fit enclosure lids and ball-and-socket joint prototypes. In short: wear-resistant flexible resin.
What is the yield strength of Durable Resin GREEN?
Durable Resin GREEN has a typical yield strength of 13 MPa (1.89 ksi) and a tensile strength of 18 MPa (2.61 ksi) — weaker than 86% of polymer grades. Strength varies by condition: see the 3 listed tempers.
Is Durable Resin GREEN easy to machine?
Not especially — machinability is rated fair (40/100, worse than 82% of polymer grades). Machinable with sharp tools, high speed and low feed, but the soft matrix smears — prefer drilling/reaming to milling and avoid coolant soak.
Can Durable Resin GREEN be welded?
Not readily — weldability is rated not recommended (5/100). Thermoset — cannot be heat welded; join with cyanoacrylate, UV-cure acrylate or two-part epoxy after light abrasion.
What surface finishes work on Durable Resin GREEN?
Sands and vapor-free polishes to a satin finish; primer + flexible paint or dyeing works, but keep parts out of sunlight or clear-coat with a UV-blocking topcoat.
Can Durable Resin GREEN be formed, bent or molded?
Print at 50–100 µm layers, orient living hinges so bending is across layers, then wash briefly in IPA (<10–15 min) and heat post-cure (typically 60–70 °C UV) to reach datasheet properties.
What is the maximum service temperature of Durable Resin GREEN?
Durable Resin GREEN is rated for continuous use to about 28°C (82 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in Durable Resin GREEN?
Yes — Durable Resin GREEN is available for injection molding and 3D printing with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- Durable Resin / Tough 1500 & Tough 2000 Resin material data sheets (SLA photopolymers) — Formlabs (2023)
- ASTM D638 / D790 / D256 / D648 test methods for plastics — ASTM International (2022)
- Photopolymer (acrylate thermoset) generic property ranges — CAMPUS / MatWeb-class polymer data (2024)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.