Aluminum 5654-H112
Temper
AA 5654 · UNS A95654 · EN AW-5654
H112 = strain hardened from hot working only
Pick for hot-rolled plate and extruded shapes where no deliberate cold work is applied but minimum properties are guaranteed.
Values for the H112 condition
Other 5654 tempers and conditions
5654 is listed in 7 conditions; see the grade overview at 5654.
Compare all 7 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
As-welded deposit | Use these numbers for design of welded joints made with 5654 filler on 5154/5254/5652-type base metal. | 105 | 215 | 17 | 52 HB | 32 % IACS |
ODefault Annealed | Default for formed sheet/plate in hydrogen-peroxide and chemical tankage where maximum ductility and lowest sensitisation risk are wanted. | 115 | 240 | 25 | 58 HB | 32.4 % IACS |
H112This page Strain hardened from hot working only | Pick for hot-rolled plate and extruded shapes where no deliberate cold work is applied but minimum properties are guaranteed. | 125 | 240 | 20 | 60 HB | 32.3 % IACS |
Strain hardened and stabilized, quarter hard | Best general-purpose sheet temper: useful strength gain while keeping good bending and welding behaviour. | 205 | 270 | 15 | 67 HB | 32.3 % IACS |
Strain hardened and stabilized, half hard | Choose where tank shell strength matters more than deep forming; still readily weldable. | 230 | 290 | 13 | 73 HB | 32.2 % IACS |
Strain hardened and stabilized, three-quarter hard | Higher-strength thin sheet for lightly formed panels and shells. | 250 | 310 | 12 | 78 HB | 127 W/m·K |
Strain hardened and stabilized, full hard | Maximum strain-hardened strength for flat or minimally formed parts; bending is limited and SCC caution applies. | 270 | 330 | 10 | 80 HB | 32.1 % IACS |
What is 5654-H112?
5654-H112 is 5654 in the H112 temper — pick for hot-rolled plate and extruded shapes where no deliberate cold work is applied but minimum properties are guaranteed. 5654-H112 has a yield strength of 125 MPa (18.1 ksi) and a tensile strength of 240 MPa (34.8 ksi) — weaker than 75% of aluminum grades. Elongation at break is 20% and the elastic modulus is 70.3 GPa (10.2 Msi). 5654-H112 has a density of 2.66 g/cm³ (0.0961 lb/in³), lighter than 84% of aluminum grades. It melts at 593°C (1,099 °F). O is the default condition FabDigit quotes; H112 is available on request or by drawing note.
Advantages
- Good corrosion resistance — 87/100, better than 100% of aluminum grades
- Readily welded — 92/100, better than 95% of aluminum grades
- Forms and bends easily — 82/100, better than 91% of aluminum grades
- Ductile — tolerates forming and impact — 20%, better than 89% of aluminum grades
- Polishes to a fine finish — 65/100, better than 82% of aluminum grades
Limitations
- Limited service temperature — 65°C (149 °F), worse than 97% of aluminum grades
- Difficult to machine — 38/100, worse than 84% of aluminum grades
- Low strength — 125 MPa (18.1 ksi), worse than 75% of aluminum grades
5654-H112 properties
Typical room-temperature values for 5654-H112; 10 are specific to this condition. Other listed values are 5654 reference data and may not represent this condition. Bars are the position among aluminum grades.
Physical3
5654-H112 has a density of 2.66 g/cm³ (0.0961 lb/in³), lighter than 84% of aluminum grades. It melts at 593°C (1,099 °F).
Mechanical11
5654-H112 has a yield strength of 125 MPa (18.1 ksi) and a tensile strength of 240 MPa (34.8 ksi) — weaker than 75% of aluminum grades. Elongation at break is 20% and the elastic modulus is 70.3 GPa (10.2 Msi).
Thermal6
5654-H112 is rated for continuous service to 65°C (149 °F). It conducts heat at 126 W/m·K (72.8 BTU/hr·ft·°F), worse than 70% of aluminum grades. Thermal expansion is 23.9 µm/m·K (13.3 µin/in·°F).
Electrical3
5654-H112 conducts electricity at 32.3 % IACS, worse than 61% of aluminum grades.
Chemical & Environmental3
Corrosion resistance is excellent (87/100), better than 100% of aluminum grades.
Sustainability4
Producing a kilogram of 5654-H112 takes about 200 MJ of energy and emits 12 kg of CO₂ — less than 60% of aluminum grades. Typical recycled content is 20%.
Manufacturability7
5654-H112's machinability is fair (38/100, worse than 84% of aluminum grades); weldability excellent (92/100); formability very good (82/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with 5654-H112
Is 5654 easy to machine?
Gummy in O/H112 — use sharp polished high-rake carbide, high speed, generous soluble-oil or alcohol-based lubricant; strain-hardened tempers chip much better.
Can 5654 be welded?
Excellent GTAW/GMAW behaviour with 5654 or 5356 filler; keep interpass temperature low and avoid prolonged >65 °C exposure to prevent Mg2Al3 grain-boundary sensitisation.
Can 5654 be formed, bent or molded?
Very good cold formability in O/H32; allow generous bend radii in H36/H38 and consider inter-anneal at 340 °C for severe drawing.
What surface finishes work on 5654?
Anodises to a clear-to-grey film and takes conversion coating and paint well; keep tooling and pickling baths free of copper and iron for peroxide-service parts.
5654 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| SiSi + Fe combined 0.45 max | ≤ 0.45 | 0.15 |
| FeSi + Fe combined 0.45 max | ≤ 0.45 | 0.25 |
| Cukept low to avoid catalysing H2O2 decomposition | ≤ 0.05 | 0.02 |
| Mn | ≤ 0.01 | 0.01 |
| Mg | 3.1 – 3.9 | 3.5 |
| Cr | 0.15 – 0.35 | 0.25 |
| Zn | ≤ 0.2 | 0.05 |
| Ti+Zrgrain refinement | 0.05 – 0.15 | 0.1 |
| Befiller wire limit in AWS A5.10; some registrations 0.0008 max | ≤ 3×10⁻⁴ | — |
| Others (each) | ≤ 0.05 | — |
| Others (total) | ≤ 0.15 | — |
| Al | balance | — |
5654-H112 — frequently asked
What is 5654-H112 used for?
5654-H112 is typically used for hydrogen peroxide storage tanks, high-purity chemical piping welds and semiconductor fluid handling. In short: copper-free peroxide-service alloy; highest formability here; filler wire and sheet.
What is the yield strength of 5654-H112?
5654-H112 has a typical yield strength of 125 MPa (18.1 ksi) and a tensile strength of 240 MPa (34.8 ksi) — weaker than 75% of aluminum grades. Strength varies by condition: see the 7 listed tempers.
Is 5654-H112 easy to machine?
Not especially — machinability is rated fair (38/100, worse than 84% of aluminum grades). Gummy in O/H112 — use sharp polished high-rake carbide, high speed, generous soluble-oil or alcohol-based lubricant; strain-hardened tempers chip much better.
Can 5654-H112 be welded?
Yes — weldability is rated excellent (92/100). Excellent GTAW/GMAW behaviour with 5654 or 5356 filler; keep interpass temperature low and avoid prolonged >65 °C exposure to prevent Mg2Al3 grain-boundary sensitisation.
What surface finishes work on 5654-H112?
Anodises to a clear-to-grey film and takes conversion coating and paint well; keep tooling and pickling baths free of copper and iron for peroxide-service parts.
Can 5654-H112 be formed, bent or molded?
Very good cold formability in O/H32; allow generous bend radii in H36/H38 and consider inter-anneal at 340 °C for severe drawing.
What is the maximum service temperature of 5654-H112?
5654-H112 is rated for continuous use to about 65°C (149 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between 5654-O and 5654-H38?
O is the default condition — default for formed sheet/plate in hydrogen-peroxide and chemical tankage where maximum ductility and lowest sensitisation risk are wanted. H38: maximum strain-hardened strength for flat or minimally formed parts; bending is limited and SCC caution applies. Yield strength is 115 MPa in O versus 270 MPa in H38.
Sources
- International Alloy Designations and Chemical Composition Limits for Wrought Aluminum (Teal Sheets) — The Aluminum Association (2018)
- ASTM B209 / B209M — Aluminum and Aluminum-Alloy Sheet and Plate — ASTM International (2021)
- AWS A5.10/A5.10M — Bare Aluminum and Aluminum-Alloy Welding Electrodes and Rods — American Welding Society (2021)
- EN 573-3 / EN 1780 Aluminium alloy designations (EN AW-5654) — CEN (2019)
- ASM Handbook Vol. 2 — Properties and Selection: Nonferrous Alloys — ASM International (1990)
- ASM Handbook Vol. 13B — Corrosion: Materials (aluminium in chemical service) — ASM International (2005)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.