Aluminum 5383-H112
Temper
AA 5383 · UNS A95383 · EN AW-5383, AW 5383
H112 = strain hardened from hot working only
Standard temper for hot-rolled heavy plate and extruded profiles where mechanical minima but no exfoliation test are required.
Values for the H112 condition
Other 5383 tempers and conditions
5383 is listed in 9 conditions; see the grade overview at 5383.
Compare all 9 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
Annealed | Pick for maximum formability in deep-drawn or heavily bent marine parts; lowest strength. | 150 | 300 | 20 | 72 HB | 29 % IACS |
Slightly strain hardened | Common for extrusions and lightly worked sheet needing good forming with slightly higher strength than O. | 175 | 310 | 17 | 78 HB | 29 % IACS |
H112This page Strain hardened from hot working only | Standard temper for hot-rolled heavy plate and extruded profiles where mechanical minima but no exfoliation test are required. | 200 | 315 | 13 | 85 HB | 29 % IACS |
Strain hardened and stabilized, quarter hard | Sheet temper for formed marine components needing a balance of strength and bendability. | 215 | 325 | 12 | 92 HB | 29 % IACS |
Strain hardened, corrosion-resistant marine temper | Default marine plate/sheet temper: highest guaranteed strength with ASTM G66/G67 exfoliation and IGC acceptance for hull and superstructure. | 220 | 330 | 13 | 95 HB | — |
Strain hardened and stabilized, marine temper | Alternative marine temper to H116 with a thermal stabilization step; specified where class rules or welding practice call for H321. | 222 | 330 | 13 | 95 HB | 29 % IACS |
Strain hardened and partially annealed, quarter hard | Quarter-hard, stabilized 5383 marine sheet — moderate strength with good forming ability and full seawater corrosion resistance. | 235 | 325 | 12 | 82 HB | 29 % IACS |
Strain hardened and stabilized, half hard | Choose for thin sheet needing higher strength and stiffness in panels with only mild forming. | 265 | 355 | 8 | 105 HB | 29 % IACS |
Strain hardened and partially annealed, half hard | Half-hard, stabilized 5383 sheet — higher strength than H22 with reduced ductility, used for marine and transport panels. | 285 | 360 | 9 | 92 HB | 29 % IACS |
What is 5383-H112?
5383-H112 is 5383 in the H112 temper — standard temper for hot-rolled heavy plate and extruded profiles where mechanical minima but no exfoliation test are required. 5383-H112 has a yield strength of 200 MPa (29 ksi) and a tensile strength of 315 MPa (45.7 ksi) — stronger than 53% of aluminum grades. Elongation at break is 13% and the elastic modulus is 71 GPa (10.3 Msi). 5383-H112 has a density of 2.66 g/cm³ (0.0961 lb/in³), lighter than 84% of aluminum grades. It melts at 574°C (1,065 °F).
Advantages
- Good corrosion resistance — 82/100, better than 99% of aluminum grades
- Readily welded — 88/100, better than 85% of aluminum grades
- Tough — resists crack growth — 32 MPa·√m (29.1 ksi·√in), better than 83% of aluminum grades
- Ductile — tolerates forming and impact — 13%, better than 79% of aluminum grades
- Forms and bends easily — 60/100, better than 77% of aluminum grades
Limitations
- Limited service temperature — 65°C (149 °F), worse than 97% of aluminum grades
- Poor heat conductor — 117 W/m·K (67.6 BTU/hr·ft·°F), worse than 83% of aluminum grades
- Low electrical conductivity — 29 % IACS, worse than 78% of aluminum grades
- Difficult to machine — 42/100, worse than 77% of aluminum grades
5383-H112 properties
Typical room-temperature values for 5383-H112; 21 are specific to this condition. Other listed values are 5383 reference data and may not represent this condition. Bars are the position among aluminum grades.
Physical3
5383-H112 has a density of 2.66 g/cm³ (0.0961 lb/in³), lighter than 84% of aluminum grades. It melts at 574°C (1,065 °F).
Mechanical12
5383-H112 has a yield strength of 200 MPa (29 ksi) and a tensile strength of 315 MPa (45.7 ksi) — stronger than 53% of aluminum grades. Elongation at break is 13% and the elastic modulus is 71 GPa (10.3 Msi).
Thermal6
5383-H112 is rated for continuous service to 65°C (149 °F). It conducts heat at 117 W/m·K (67.6 BTU/hr·ft·°F), worse than 83% of aluminum grades. Thermal expansion is 24.2 µm/m·K (13.4 µin/in·°F).
Electrical3
5383-H112 conducts electricity at 29 % IACS, worse than 78% of aluminum grades.
Chemical & Environmental3
Corrosion resistance is very good (82/100), better than 99% of aluminum grades.
Sustainability4
Producing a kilogram of 5383-H112 takes about 205 MJ of energy and emits 12.5 kg of CO₂ — more than 76% of aluminum grades. Typical recycled content is 35%.
Manufacturability8
5383-H112's machinability is fair (42/100, worse than 77% of aluminum grades); weldability excellent (88/100); formability good (60/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with 5383-H112
Is 5383 easy to machine?
Gummy, long stringy chips — use sharp polished high-rake carbide, high speed, generous flood or MQL lubricant; expect built-up edge if speeds are low.
Can 5383 be welded?
Excellent for MIG/TIG (ER5183 preferred, ER5356 acceptable) and FSW; HAZ softens to near-O strength, so design joints to annealed-temper allowables and keep interpass temperature low.
Can 5383 be formed, bent or molded?
Good cold formability in O/H111; H116/H321 plate needs generous bend radii (≈2–3 t) and transverse bending is preferred over longitudinal.
What surface finishes work on 5383?
Takes protective clear/hard anodizing and marine epoxy primers well; decorative bright anodize is only fair, and chromate-free conversion coatings are standard for painted hull structures.
5383 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Si | ≤ 0.25 | 0.1 |
| Fe | ≤ 0.25 | 0.15 |
| Cu | ≤ 0.2 | 0.05 |
| Mn | 0.7 – 1 | 0.85 |
| Mg | 4 – 5.2 | 4.7 |
| Cr | ≤ 0.25 | 0.1 |
| Zn | ≤ 0.4 | 0.2 |
| Ti | ≤ 0.15 | 0.03 |
| Zrgrain-structure control, key difference vs 5083 | ≤ 0.2 | 0.12 |
| Others (each) | ≤ 0.05 | — |
| Others (total) | ≤ 0.15 | — |
| Al | balance | — |
5383-H112 — frequently asked
What is 5383-H112 used for?
5383-H112 is typically used for fast ferry hulls, high-speed yacht hulls, ship superstructure panels, LNG and cryogenic structural plate, offshore platform decks and modules and patrol and workboat hulls. In short: improved corrosion 5083.
What is the yield strength of 5383-H112?
5383-H112 has a typical yield strength of 200 MPa (29 ksi) and a tensile strength of 315 MPa (45.7 ksi) — stronger than 53% of aluminum grades. Strength varies by condition: see the 9 listed tempers.
Is 5383-H112 easy to machine?
Not especially — machinability is rated fair (42/100, worse than 77% of aluminum grades). Gummy, long stringy chips — use sharp polished high-rake carbide, high speed, generous flood or MQL lubricant; expect built-up edge if speeds are low.
Can 5383-H112 be welded?
Yes — weldability is rated excellent (88/100). Excellent for MIG/TIG (ER5183 preferred, ER5356 acceptable) and FSW; HAZ softens to near-O strength, so design joints to annealed-temper allowables and keep interpass temperature low.
What surface finishes work on 5383-H112?
Takes protective clear/hard anodizing and marine epoxy primers well; decorative bright anodize is only fair, and chromate-free conversion coatings are standard for painted hull structures.
Can 5383-H112 be formed, bent or molded?
Good cold formability in O/H111; H116/H321 plate needs generous bend radii (≈2–3 t) and transverse bending is preferred over longitudinal.
What is the maximum service temperature of 5383-H112?
5383-H112 is rated for continuous use to about 65°C (149 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in 5383-H112?
Yes — 5383-H112 is available for CNC machining and sheet metal; every part is priced by an engineer rather than instantly. Upload a STEP file to get a price and a DFM check.
Sources
- International Alloy Designations and Chemical Composition Limits for Wrought Aluminum (Teal Sheets) — The Aluminum Association (2018)
- EN 485-2 Aluminium and aluminium alloys — Sheet, strip and plate — Mechanical properties — CEN (2016)
- ASTM B928/B928M Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service — ASTM International (2019)
- ASM Handbook Vol. 2: Properties and Selection — Nonferrous Alloys — ASM International (1990)
- Marine plate alloy 5383 H116/H321 data sheet — Aleris/Corus Aluminium Rolled Products (2010)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.