Aluminum 1070 · temper
Aluminum 1070-H24
Properties of the H24 condition, compared with the other 1070 tempers.
Half-hard sheet with restored ductility — preferred over H14 when tight bends or spinning are required.
What is 1070-H24?
1070-H24 is 1070 in the H24 temper — half-hard sheet with restored ductility — preferred over H14 when tight bends or spinning are required. 1070-H24 has a yield strength of 80 MPa (11.6 ksi) and a tensile strength of 105 MPa (15.2 ksi) — weaker than 90% of aluminum grades. Elongation at break is 11% and the elastic modulus is 69 GPa (10 Msi). 1070-H24 has a density of 2.71 g/cm³ (0.0977 lb/in³), lighter than 54% of aluminum grades. It melts at 646°C (1,195 °F).
Advantages
- Conducts heat well — 225 W/m·K (130 BTU/hr·ft·°F), better than 95% of aluminum grades
- High electrical conductivity — 58.8 % IACS, better than 95% of aluminum grades
- Readily welded — 92/100, better than 95% of aluminum grades
- Good corrosion resistance — 78/100, better than 94% of aluminum grades
- Forms and bends easily — 82/100, better than 91% of aluminum grades
Limitations
- Low strength — 80 MPa (11.6 ksi), worse than 90% of aluminum grades
- Difficult to machine — 35/100, worse than 86% of aluminum grades
1070-H24 properties
Typical room-temperature values for 1070-H24 — 8 properties are specific to this condition; the rest are grade-level values shared by every 1070 temper. Each bar shows where the value sits among the aluminum grades in FabDigit's library — further right is higher.
Physical3
1070-H24 has a density of 2.71 g/cm³ (0.0977 lb/in³), lighter than 54% of aluminum grades. It melts at 646°C (1,195 °F).
Mechanical10
1070-H24 has a yield strength of 80 MPa (11.6 ksi) and a tensile strength of 105 MPa (15.2 ksi) — weaker than 90% of aluminum grades. Elongation at break is 11% and the elastic modulus is 69 GPa (10 Msi).
Thermal6
1070-H24 is rated for continuous service to 150°C (302 °F). It conducts heat at 225 W/m·K (130 BTU/hr·ft·°F), better than 95% of aluminum grades. Thermal expansion is 23.6 µm/m·K (13.1 µin/in·°F).
Electrical3
1070-H24 conducts electricity at 58.8 % IACS, better than 95% of aluminum grades.
Chemical & Environmental3
Corrosion resistance is very good (78/100), better than 94% of aluminum grades.
Sustainability4
Producing a kilogram of 1070-H24 takes about 205 MJ of energy and emits 12.5 kg of CO₂ — more than 75% of aluminum grades. Typical recycled content is 10%.
Manufacturability7
1070-H24's machinability is fair (35/100, worse than 86% of aluminum grades); weldability excellent (92/100); formability very good (82/100).
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Other 1070 tempers and conditions
1070 is also supplied in 10 other conditions. The full side-by-side table is on the 1070 overview.
- H18Full-hard strip/foil for maximum work-hardened strength, springy flatness and clean blanking.122 MPa yield · 35 HB
- H16Choose for flat strip and stamped parts needing higher stiffness with only gentle bends.105 MPa yield · 33 HB
- H14Most common cold-worked sheet temper: better handling strength and flatness with moderate bending ability.92 MPa yield · 30 HB
- H24Half-hard sheet with restored ductility — preferred over H14 when tight bends or spinning are required.80 MPa yield · 31 HB
- H12Light cold work when slightly more stiffness/handling strength is needed but forming is still required.70 MPa yield · 25 HB
- H112Hot-worked extrusion/plate temper of 99.7% pure aluminium retaining slight work hardening, giving strength just above annealed with very high ductility and conductivity.40 MPa yield · 22 HB
- ODefault stock condition for foil, deep-drawn parts, capacitor/conductor strip and anything needing maximum ductility and conductivity.25 MPa yield · 19 HB
Working with 1070-H24
Is 1070 easy to machine?
Very soft and gummy — use polished high-rake tools, sharp inserts, high speed with low feed and generous lubricant; consider H18 temper or 6061 substitution for machined parts.
Can 1070 be welded?
Excellent with TIG/MIG using 1100 or 1188 filler (1070 wire for conductor work); resistance and friction-stir welding also fine, but weld metal reverts to annealed strength.
Can 1070 be formed, bent or molded?
Outstanding deep drawing, spinning, roll forming and foil rolling in O/H2x tempers; springback is low but the material galls, so use good lubrication and polished dies.
What surface finishes work on 1070?
Anodizes to clear, bright films (standard for reflectors and bright trim); accepts chemical brightening, chromate/chrome-free conversion coating and paint, but the soft surface dents and scratches easily.
1070 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| SiAA limit; EN AW-1070A limits Si 0.20 | ≤ 0.2 | 0.08 |
| Fe | ≤ 0.25 | 0.15 |
| Cu | ≤ 0.04 | 0.01 |
| Mn | ≤ 0.03 | 0.01 |
| Mg | ≤ 0.03 | 0.01 |
| Zn | ≤ 0.04 | 0.01 |
| Ti | ≤ 0.03 | 0.01 |
| V | ≤ 0.05 | 0.01 |
| Others (each)each other element | ≤ 0.03 | — |
| Alminimum aluminium content defines the grade | ≥ 99.7 (balance) | — |
1070-H24 — frequently asked
What is 1070-H24 used for?
1070-H24 is typically used for electrical conductors and busbars, chemical processing tanks and liners, deep-drawn and spun vessels, foil and thin strip, reflector sheet and bright trim and heat transfer fin stock. In short: very high purity; high conductivity.
What is the yield strength of 1070-H24?
1070-H24 has a typical yield strength of 80 MPa (11.6 ksi) and a tensile strength of 105 MPa (15.2 ksi) — weaker than 90% of aluminum grades. Strength varies by condition: see the 11 listed tempers.
Is 1070-H24 easy to machine?
Not especially — machinability is rated fair (35/100, worse than 86% of aluminum grades). Very soft and gummy — use polished high-rake tools, sharp inserts, high speed with low feed and generous lubricant; consider H18 temper or 6061 substitution for machined parts.
Can 1070-H24 be welded?
Yes — weldability is rated excellent (92/100). Excellent with TIG/MIG using 1100 or 1188 filler (1070 wire for conductor work); resistance and friction-stir welding also fine, but weld metal reverts to annealed strength.
What surface finishes work on 1070-H24?
Anodizes to clear, bright films (standard for reflectors and bright trim); accepts chemical brightening, chromate/chrome-free conversion coating and paint, but the soft surface dents and scratches easily.
Can 1070-H24 be formed, bent or molded?
Outstanding deep drawing, spinning, roll forming and foil rolling in O/H2x tempers; springback is low but the material galls, so use good lubrication and polished dies.
What is the maximum service temperature of 1070-H24?
1070-H24 is rated for continuous use to about 150°C (302 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in 1070-H24?
Yes — 1070-H24 is available for CNC machining and sheet metal with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- International Alloy Designations and Chemical Composition Limits for Wrought Aluminum (Teal Sheets) — The Aluminum Association (2018)
- EN 573-3 / EN 485-2 — Aluminium and aluminium alloys: composition and sheet properties — CEN (2019)
- ASM Handbook Vol.2 — Properties and Selection: Nonferrous Alloys — ASM International (1990)
- Commercially pure aluminium 1070/1070A sheet, strip and foil datasheets — various mills (Chalco, Constellium, Alcoa) (2023)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.