PA11 · additive grade
PA11 COND
Properties of the COND condition, compared with the other PA11 grades.
PA11 moisture-conditioned to equilibrium at 50% RH: water plasticizes the amide phase, lowering modulus and strength while raising ductility and impact toughness.
What is PA11 COND?
PA11 COND is PA11 in the COND grade — pA11 moisture-conditioned to equilibrium at 50% RH: water plasticizes the amide phase, lowering modulus and strength while raising ductility and impact toughness. PA11 COND has a yield strength of 36 MPa (5.22 ksi) and a tensile strength of 45 MPa (6.53 ksi) — weaker than 68% of polymer grades. Elongation at break is 120% and the elastic modulus is 1.1 GPa (0.152 Msi). PA11 COND has a density of 1.04 g/cm³ (0.0376 lb/in³), lighter than 70% of polymer grades. Its glass-transition temperature is 32°C (90 °F). Unfilled is the default condition FabDigit quotes; COND is available on request or by drawing note.
Advantages
- Tough — resists crack growth — 3.5 MPa·√m (3.19 ksi·√in), better than 80% of polymer grades
- Conducts heat well — 0.29 W/m·K (0.168 BTU/hr·ft·°F), better than 79% of polymer grades
- Good UV / weathering resistance — 55/100, better than 77% of polymer grades
PA11 COND properties
Typical room-temperature values for PA11 COND — 44 properties are specific to this condition; the rest are grade-level values shared by every PA11 grade. Each bar shows where the value sits among the polymer grades in FabDigit's library — further right is higher.
Physical5
PA11 COND has a density of 1.04 g/cm³ (0.0376 lb/in³), lighter than 70% of polymer grades. Its glass-transition temperature is 32°C (90 °F).
Mechanical13
PA11 COND has a yield strength of 36 MPa (5.22 ksi) and a tensile strength of 45 MPa (6.53 ksi) — weaker than 68% of polymer grades. Elongation at break is 120% and the elastic modulus is 1.1 GPa (0.152 Msi).
Thermal11
PA11 COND is rated for continuous service to 80°C (176 °F). It conducts heat at 0.29 W/m·K (0.168 BTU/hr·ft·°F), better than 79% of polymer grades. Thermal expansion is 130 µm/m·K (72.2 µin/in·°F).
Electrical6
PA11 COND is an electrical insulator with a dielectric strength of 20 kV/mm (508 V/mil) and a resistivity of 1×10¹⁰ Ω·m.
Chemical & Environmental3
Corrosion resistance is very good (80/100), worse than 55% of polymer grades. UV resistance is good.
Sustainability3
Producing a kilogram of PA11 COND takes about 70 MJ of energy and emits 4 kg of CO₂ — less than 94% of polymer grades. Typical recycled content is 40%.
Manufacturability6
PA11 COND's machinability is good (62/100, better than 59% of polymer grades); weldability good (68/100).
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Other PA11 grades and fills
PA11 is also supplied in 8 other conditions. The full side-by-side table is on the PA11 overview.
- UnfilledDefaultDefault choice for tough, ductile functional prototypes and end-use snap-fits, living hinges, ducts and footwear parts.48 MPa tensile
- CFHighest stiffness-to-weight printed PA11; for jigs, brackets and motorsport parts where deflection must be minimized.65 MPa tensile
- MJFPick for higher-throughput, near-isotropic parts with fine detail; slightly denser and more anisotropic in elongation than SLS.49 MPa tensile
- DAMPA11 tested dry-as-molded/printed (≤0.2% moisture): highest stiffness and strength, lower notched impact and slightly lower dielectric losses.45 MPa yield · 75 Shore D
- GFUse when stiffness, dimensional stability and elevated-temperature rigidity matter more than ductility.42 MPa tensile
- CONDPA11 moisture-conditioned to equilibrium at 50% RH: water plasticizes the amide phase, lowering modulus and strength while raising ductility and impact toughness.36 MPa yield · 72 Shore D
Working with PA11 COND
Is PA11 easy to machine?
Machines cleanly with sharp, high-rake tools and air cooling; tough and slightly gummy, so use climb milling and avoid heat build-up that closes drilled holes.
Can PA11 be welded?
Hot-plate, hot-gas, ultrasonic and laser welding all work on PA11; solvent bonding is impractical — use cyanoacrylate or two-part polyurethane/epoxy after plasma or abrasive prep.
Can PA11 be formed, bent or molded?
Print with bed ~185–190 °C and slow, uniform cooling to limit curl; reuse powder at 30–70% refresh, dry powder before use, and scale parts ~2.5–3.5% for sinter shrinkage.
What surface finishes work on PA11?
Bead blasting, vibratory tumbling, chemical vapor smoothing and dyeing (black/colored) work well; PA11's low moisture pickup keeps dyed and painted parts dimensionally stable, but UV-stabilized topcoat is advised outdoors.
PA11 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| flow/anti-caking additive (fumed silica)powder-bed processing aid | 0.05 – 0.5 | 0.2 |
| pigment (carbon black, black grades)PA1102 / MJF black grades only | 0.1 – 1.5 | 0.5 |
| poly(11-aminoundecanoic acid) / PA11 homcastor-oil derived, ~100% bio-based carbon; base unfilled powder | balance | — |
PA11 COND — frequently asked
What is PA11 COND used for?
PA11 COND is typically used for flexible fuel lines, pneumatic tubing, living hinges and snap-fit enclosures, footwear midsoles, automotive functional brackets and ducts and sports equipment components. In short: flexible; durable nylon.
What is the yield strength of PA11 COND?
PA11 COND has a typical yield strength of 36 MPa (5.22 ksi) and a tensile strength of 45 MPa (6.53 ksi) — weaker than 68% of polymer grades. Strength varies by condition: see the 9 listed tempers.
Is PA11 COND easy to machine?
Reasonably — machinability is rated good (62/100, better than 59% of polymer grades). Machines cleanly with sharp, high-rake tools and air cooling; tough and slightly gummy, so use climb milling and avoid heat build-up that closes drilled holes.
Can PA11 COND be welded?
Yes — weldability is rated good (68/100). Hot-plate, hot-gas, ultrasonic and laser welding all work on PA11; solvent bonding is impractical — use cyanoacrylate or two-part polyurethane/epoxy after plasma or abrasive prep.
What surface finishes work on PA11 COND?
Bead blasting, vibratory tumbling, chemical vapor smoothing and dyeing (black/colored) work well; PA11's low moisture pickup keeps dyed and painted parts dimensionally stable, but UV-stabilized topcoat is advised outdoors.
Can PA11 COND be formed, bent or molded?
Print with bed ~185–190 °C and slow, uniform cooling to limit curl; reuse powder at 30–70% refresh, dry powder before use, and scale parts ~2.5–3.5% for sinter shrinkage.
What is the maximum service temperature of PA11 COND?
PA11 COND is rated for continuous use to about 80°C (176 °F), and briefly to 135°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between PA11 Unfilled and PA11-DAM?
Unfilled is the default condition — default choice for tough, ductile functional prototypes and end-use snap-fits, living hinges, ducts and footwear parts. DAM: pA11 tested dry-as-molded/printed (≤0.2% moisture): highest stiffness and strength, lower notched impact and slightly lower dielectric losses. Yield strength is 36 MPa in Unfilled versus 45 MPa in DAM.
Can FabDigit make parts in PA11 COND?
Yes — PA11 COND is available for 3D printing with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- PA 1101 / PA 1102 black laser-sintering material data sheet — EOS GmbH (2023)
- HP 3D High Reusability PA 11 material data sheet — HP Inc. (2023)
- Rilsan PA11 resin and fine-powder technical data — Arkema (2022)
- PA 11 / PA 11-GF / PA 11-ESD laser sintering powders — Advanced Laser Materials (EOS North America) (2022)
- CAMPUS polyamide 11 property records — CWFG / CAMPUS consortium (2023)
- Engineered Materials Handbook Vol. 2: Engineering Plastics — ASM International (1988)
- ISO 527-2 / ISO 178 / ISO 75 plastics test methods — ISO (2019)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.