Steel AF1410
UNS K92571
AF1410 (UNS K92571) is a nickel-cobalt-chromium secondary-hardening ultra-high-strength steel developed for landing gear and arresting-hook shanks, delivering 1520 MPa yield and 1660 MPa tensile at 48 HRC with 16 % elongation.
Reference datasheet — AF1410 is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the Aged 950F condition
AF1410 tempers and conditions
AF1410 is supplied in 7 conditions, soft to hard. Aged 950F is the default FabDigit quotes; the values on this page are for it.
Compare all 7 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
machining condition | Softest supplied condition for rough machining and forming before final heat treatment. | 830 | 1,030 | 20 | 31 HRC | — |
Austenitized 830 °C, quenched + refrigerated | Intermediate as-quenched martensite; not a service condition — must be aged. | 970 | 1,310 | 18 | 41 HRC | 2.5 % IACS |
Normalized ≈900 °C, air cool | Grain-refining pre-treatment before austenitize/quench/age; supplied on some bar orders. | 1,100 | 1,400 | 17 | 42 HRC | 2.8 % IACS |
As-welded + re-aged (GTAW with matching filler) | Weld joint condition after post-weld re-aging; joint efficiency typically 90–95 % of base metal. | 1,400 | 1,550 | 12 | 46 HRC | 2.7 % IACS |
Q + aged 538 °C | Use where fracture toughness and SCC resistance outrank peak strength. | 1,420 | 1,540 | 17 | 45 HRC | — |
Aged 950FDefault Q + aged 510 °C (950 °F) 5 h, air cool | The standard aerospace condition: ~1650 MPa with ~155 MPa·√m toughness for landing gear and hook shanks. | 1,520 | 1,660 | 16 | 48 HRC | — |
Q + aged 482 °C (900 °F) 5 h | Choose when maximum strength is required and toughness demand is moderate. | 1,620 | 1,790 | 14 | 52 HRC | — |
What is AF1410?
AF1410 (UNS K92571) is a nickel-cobalt-chromium secondary-hardening ultra-high-strength steel developed for landing gear and arresting-hook shanks, delivering 1520 MPa yield and 1660 MPa tensile at 48 HRC with 16 % elongation. Its low carbon content gives high fracture toughness at the 1600–1700 MPa strength level and better weldability (score 60) than 300M or 4340; it is available as forgings, bar and plate. It is not corrosion resistant, is limited to about 400 °C service, and machines slowly (score 22). AerMet 100 or AerMet 310 is the step up when higher strength is required. AF1410 has a density of 7.89 g/cm³ (0.285 lb/in³), heavier than 93% of steel grades. It melts at 1,425°C (2,597 °F). AF1410 has a yield strength of 1,520 MPa (220 ksi) and a tensile strength of 1,660 MPa (241 ksi) — stronger than 97% of steel grades. Elongation at break is 16% and the elastic modulus is 196 GPa (28.4 Msi).
What is AF1410 used for?
- landing gear forgings
- arresting hook shanks
- high-toughness structural members
Advantages
- High strength — 1,520 MPa (220 ksi), better than 97% of steel grades
- Tough — resists crack growth — 154 MPa·√m (140.1 ksi·√in), better than 97% of steel grades
- Polishes to a fine finish — 75/100, better than 94% of steel grades
Limitations
- High embodied carbon — 6.5 kg CO₂/kg, worse than 98% of steel grades
- Low electrical conductivity — 2.7 % IACS, worse than 96% of steel grades
- Difficult to machine — 22/100, worse than 95% of steel grades
- Poor heat conductor — 24 W/m·K (13.9 BTU/hr·ft·°F), worse than 90% of steel grades
- Limited formability — 15/100, worse than 87% of steel grades
AF1410 properties
Typical room-temperature values for AF1410-Aged 950F; bars are the position among steel grades.
Physical3
AF1410 has a density of 7.89 g/cm³ (0.285 lb/in³), heavier than 93% of steel grades. It melts at 1,425°C (2,597 °F).
Mechanical15
AF1410 has a yield strength of 1,520 MPa (220 ksi) and a tensile strength of 1,660 MPa (241 ksi) — stronger than 97% of steel grades. Elongation at break is 16% and the elastic modulus is 196 GPa (28.4 Msi).
Thermal6
AF1410 is rated for continuous service to 400°C (752 °F). It conducts heat at 24 W/m·K (13.9 BTU/hr·ft·°F), worse than 90% of steel grades. Thermal expansion is 11.6 µm/m·K (6.44 µin/in·°F).
Electrical3
AF1410 conducts electricity at 2.7 % IACS, worse than 96% of steel grades.
Chemical & Environmental3
Corrosion resistance is poor (18/100), better than 83% of steel grades.
Sustainability4
Producing a kilogram of AF1410 takes about 78 MJ of energy and emits 6.5 kg of CO₂ — more than 98% of steel grades. Typical recycled content is 15%.
Manufacturability5
AF1410's machinability is poor (22/100, worse than 95% of steel grades); weldability good (60/100); formability poor (15/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the steel family
Yield strength against density for every steel grade FabDigit runs. AF1410 is highlighted; hover a dot for its name, or open the interactive family chart.
Working with AF1410
Is AF1410 easy to machine?
Rough machine in the overaged/annealed condition (~31 HRC); finish at 48 HRC with rigid setups, carbide or CBN, low speed and heavy positive rake, and leave grind stock on critical surfaces.
Can AF1410 be welded?
Better weldable than 300M/4340 thanks to the low carbon: GTAW/EBW with matching filler, clean dry conditions, no preheat required, and re-age at the original aging temperature after welding.
Can AF1410 be formed, bent or molded?
Hot work 1050–1150 °C then normalize; cold forming is impractical in any hardened condition — form only in the annealed state with generous radii.
AF1410 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| C | 0.13 – 0.17 | 0.15 |
| Ni | 9.5 – 10.5 | 10 |
| Co | 13.5 – 14.5 | 14 |
| Cr | 1.8 – 2.2 | 2 |
| Mo | 0.9 – 1.1 | 1 |
| Mn | ≤ 0.1 | 0.03 |
| Si | ≤ 0.1 | 0.03 |
| P | ≤ 0.01 | 0 |
| S | ≤ 0.01 | 0 |
| Timax, residual | ≤ 0.02 | 0.01 |
| Omax, VIM-VAR cleanliness | ≤ 0 | 8×10⁻⁴ |
| Fe | balance |
What surface finishes work on AF1410?
Grind carefully to avoid grinding burn; protect with Cd or IVD-aluminium plating (or Al-ceramic coatings) plus a 190 °C hydrogen embrittlement relief bake within 4 h of plating; shot peen fillets for fatigue life.
Surface treatments FabDigit runs on steel parts — pick them in the quote configurator or call them out on the drawing. Each links to its datasheet in the surface-finish library (thickness, specs, call-out, material verdicts).
Organic Coating
Black / Phosphate
Thermal Spray
Equivalent designations
Standards and trade names that resolve to Steel AF1410 in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- UNS
- K92571
How much does AF1410 cost?
AF1410 is a high-cost steel ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
AF1410 — frequently asked
What is AF1410 used for?
AF1410 is typically used for landing gear forgings, arresting hook shanks and high-toughness structural members. In short: weldable UHS steel; tougher than 300M; landing gear forging grade.
What is the yield strength of AF1410?
AF1410 has a typical yield strength of 1,520 MPa (220 ksi) and a tensile strength of 1,660 MPa (241 ksi) — stronger than 97% of steel grades. Strength varies by condition: see the 7 listed tempers.
Is AF1410 easy to machine?
Not especially — machinability is rated poor (22/100, worse than 95% of steel grades). Rough machine in the overaged/annealed condition (~31 HRC); finish at 48 HRC with rigid setups, carbide or CBN, low speed and heavy positive rake, and leave grind stock on critical surfaces.
Can AF1410 be welded?
Yes — weldability is rated good (60/100). Better weldable than 300M/4340 thanks to the low carbon: GTAW/EBW with matching filler, clean dry conditions, no preheat required, and re-age at the original aging temperature after welding.
What surface finishes work on AF1410?
Grind carefully to avoid grinding burn; protect with Cd or IVD-aluminium plating (or Al-ceramic coatings) plus a 190 °C hydrogen embrittlement relief bake within 4 h of plating; shot peen fillets for fatigue life.
Can AF1410 be formed, bent or molded?
Hot work 1050–1150 °C then normalize; cold forming is impractical in any hardened condition — form only in the annealed state with generous radii.
What is the maximum service temperature of AF1410?
AF1410 is rated for continuous use to about 400°C (752 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between AF1410 Aged 950F and AF1410 SHT-Q?
Aged 950F is the default condition — the standard aerospace condition: ~1650 MPa with ~155 MPa·√m toughness for landing gear and hook shanks. SHT-Q: intermediate as-quenched martensite; not a service condition — must be aged. Yield strength is 1,520 MPa in Aged 950F versus 970 MPa in SHT-Q.
How much does AF1410 cost?
AF1410 is a high-cost steel ($$$$), pricier than about 78% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- AMS 6527 — Steel Bars, Forgings, Tubing 14Co-10Ni-2Cr-1Mo (AF1410), Consumable Electrode Vacuum Melted — SAE International (2019)
- AMS 6528 — AF1410 Steel Plate and Sheet — SAE International (2018)
- ASM Handbook Vol. 1: Properties and Selection — Irons, Steels, and High-Performance Alloys (Ultrahigh-Strength Steels) — ASM International (1990)
- ASM Handbook Vol. 19: Fatigue and Fracture — ASM International (1996)
- MMPDS — Metallic Materials Properties Development and Standardization (high-strength steel chapters) — Battelle/FAA (2023)
- Ni-Co secondary-hardening ultra-high-strength steel bar datasheets (Carpenter/Latrobe/Universal Stainless class products) — Specialty steel producers (2022)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.