PESU ESD
Grade
ISO 1043 PES · also Ultrason E, Sumikaexcel
ESD = eSD / static-dissipative compound
Carbon-black or carbon-fiber loaded compound for wafer handling and electronics fixtures needing 10^4–10^9 Ω surface.
Values for the ESD condition
Other PESU grades and fills
PESU is listed in 8 conditions; see the grade overview at PESU.
Compare all 8 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
Bearing grade | Internally lubricated compound for high-temperature bushings, seal rings and wear pads. | 60 | 62 | 8 | 85 Shore D |
ESDThis page ESD / static-dissipative compound | Carbon-black or carbon-fiber loaded compound for wafer handling and electronics fixtures needing 10^4–10^9 Ω surface. | 78 | 80 | 5 | 88 Shore D |
Membrane grade resin/powder | High-purity, narrow-MW resin dissolved in NMP/DMAc for phase-inversion UF, MF and hemodialysis membranes. | 84 | 85 | 40 | 87 Shore D |
10% glass-fiber reinforced | Light reinforcement when moderate stiffness gain is needed with retained toughness. | — | 100 | 5 | — |
20% glass-fiber reinforced | Mid-level stiffness/creep upgrade for structural housings and connectors. | — | 125 | 3 | — |
30% glass-fiber reinforced | Workhorse reinforced grade for aircraft interior brackets, high-temperature structural and electrical parts. | — | 150 | 2.5 | 92 HRM |
40% glass-fiber reinforced | Maximum stiffness and lowest CTE glass grade for load-bearing high-temperature components. | — | 165 | 1.8 | — |
30% carbon-fiber reinforced | Choose for maximum specific stiffness, low CTE and static-dissipative behaviour in hot service. | — | 190 | 1.5 | — |
What is PESU ESD?
PESU ESD is PESU in the ESD grade — carbon-black or carbon-fiber loaded compound for wafer handling and electronics fixtures needing 10^4–10^9 Ω surface. PESU ESD has a yield strength of 78 MPa (11.3 ksi) and a tensile strength of 80 MPa (11.6 ksi) — stronger than 86% of polymer grades. Elongation at break is 5% and the elastic modulus is 3.3 GPa (0.479 Msi). PESU ESD has a density of 1.42 g/cm³ (0.0513 lb/in³), heavier than 83% of polymer grades. Its glass-transition temperature is 225°C (437 °F).
Advantages
- High strength — 78 MPa (11.3 ksi), better than 86% of polymer grades
- Polishes to a fine finish — 75/100, better than 86% of polymer grades
- High service temperature — 180°C (356 °F), better than 85% of polymer grades
- Stiff — 3.3 GPa (0.479 Msi), better than 80% of polymer grades
- Conducts heat well — 0.28 W/m·K (0.162 BTU/hr·ft·°F), better than 79% of polymer grades
Limitations
- Heavy — 1.42 g/cm³ (0.0513 lb/in³), worse than 83% of polymer grades
- High embodied carbon — 8 kg CO₂/kg, worse than 83% of polymer grades
- Limited formability — 15/100, worse than 79% of polymer grades
- Degrades in UV without stabilisers — 25/100, worse than 76% of polymer grades
PESU ESD properties
Typical room-temperature values for PESU ESD; 27 are specific to this condition. Other listed values are PESU reference data and may not represent this condition. Bars are the position among polymer grades.
Physical6
PESU ESD has a density of 1.42 g/cm³ (0.0513 lb/in³), heavier than 83% of polymer grades. Its glass-transition temperature is 225°C (437 °F).
Mechanical17
PESU ESD has a yield strength of 78 MPa (11.3 ksi) and a tensile strength of 80 MPa (11.6 ksi) — stronger than 86% of polymer grades. Elongation at break is 5% and the elastic modulus is 3.3 GPa (0.479 Msi).
Thermal11
PESU ESD is rated for continuous service to 180°C (356 °F). It conducts heat at 0.28 W/m·K (0.162 BTU/hr·ft·°F), better than 79% of polymer grades. Thermal expansion is 55 µm/m·K (30.6 µin/in·°F).
Electrical7
PESU ESD is an electrical insulator with a dielectric strength of 17 kV/mm (431.8 V/mil) and a resistivity of 10,000 Ω·m.
Chemical & Environmental3
Corrosion resistance is very good (80/100), worse than 52% of polymer grades. UV resistance is poor.
Sustainability4
Producing a kilogram of PESU ESD takes about 150 MJ of energy and emits 8 kg of CO₂ — more than 84% of polymer grades. Typical recycled content is 0%.
Manufacturability8
PESU ESD's machinability is good (55/100, worse than 64% of polymer grades); weldability poor (20/100); formability poor (15/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with PESU ESD
Is PESU easy to machine?
Machines cleanly with sharp carbide tools, positive rake and generous air/mist cooling; avoid cutting fluids containing ketones/esters and stress-relieve annealed blanks (~180 °C) before finish cuts to prevent crazing.
Can PESU be welded?
Joinable by ultrasonic, hot-plate, IR and vibration welding as well as solvent bonding (NMP/DMAc) and high-temperature epoxy adhesives; parts must be dried first or weld porosity occurs.
Can PESU be formed, bent or molded?
Inject at 340–380 °C melt with 140–180 °C mold; resin must be dried 3–4 h at 150 °C to <0.02 % moisture. Sheet thermoforms above ~230 °C; high melt viscosity requires generous gates and runners.
What surface finishes work on PESU?
Amber transparent surface polishes well and accepts vacuum metallizing, hard coats and pad printing; UV-stabilizing pigment or coating is required for outdoor exposure to limit yellowing.
PESU chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| glass fiber0 in default unfilled grade; 10–40 wt% in GF variants | 0 – 40 | 0 |
| carbon fiberCF reinforced compounds only | 0 – 30 | 0 |
| PTFE / graphite lubricantbearing grades only | 0 – 20 | 0 |
| polyethersulfone repeat unit (–C6H4–SO2–amorphous polyarylethersulfone from 4,4'-dichlorodiphenyl sulfone + bisphenol S salt; ISO 1043 code PES/PESU | balance | — |
PESU ESD — frequently asked
What is PESU ESD used for?
PESU ESD is typically used for aircraft interior components, microwave cookware, gas separation membranes, electrical insulation and medical sterilization trays. In short: highest-heat sulfone after PPSU; inherently flame retardant; machinable transparent high-temp resin.
What is the yield strength of PESU ESD?
PESU ESD has a typical yield strength of 78 MPa (11.3 ksi) and a tensile strength of 80 MPa (11.6 ksi) — stronger than 86% of polymer grades. Strength varies by condition: see the 8 listed tempers.
Is PESU ESD easy to machine?
Reasonably — machinability is rated good (55/100, worse than 64% of polymer grades). Machines cleanly with sharp carbide tools, positive rake and generous air/mist cooling; avoid cutting fluids containing ketones/esters and stress-relieve annealed blanks (~180 °C) before finish cuts to prevent crazing.
Can PESU ESD be welded?
Not readily — weldability is rated poor (20/100). Joinable by ultrasonic, hot-plate, IR and vibration welding as well as solvent bonding (NMP/DMAc) and high-temperature epoxy adhesives; parts must be dried first or weld porosity occurs.
What surface finishes work on PESU ESD?
Amber transparent surface polishes well and accepts vacuum metallizing, hard coats and pad printing; UV-stabilizing pigment or coating is required for outdoor exposure to limit yellowing.
Can PESU ESD be formed, bent or molded?
Inject at 340–380 °C melt with 140–180 °C mold; resin must be dried 3–4 h at 150 °C to <0.02 % moisture. Sheet thermoforms above ~230 °C; high melt viscosity requires generous gates and runners.
What is the maximum service temperature of PESU ESD?
PESU ESD is rated for continuous use to about 180°C (356 °F), and briefly to 220°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Sources
- Ultrason E (PESU) product line and processing guide — BASF (2023)
- Sumikaexcel PES grade data — Sumitomo Chemical (2022)
- TECASON E stock shape datasheet — Ensinger (2023)
- CAMPUS plastics database — PESU ISO 10350 datasets — CWFG / CAMPUS consortium (2024)
- ISO 1043-1 Plastics — Symbols and abbreviated terms — ISO (2011)
- ISO 527 / ISO 75 / ISO 306 test methods — ISO (2019)
- Engineering Plastics — Engineered Materials Handbook Vol.2 — ASM International (1988)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.