mPPE PPE-PP
Matrix
also Noryl
PPE-PP = pPE+PP alloy
Low-density, hydrolysis- and chemical-resistant alloy used for EV battery packs and photovoltaic hardware where light weight plus non-halogen FR matters.
Values for the PPE-PP condition
Other mPPE grades and fills
mPPE is listed in 12 conditions; see the grade overview at mPPE.
Compare all 12 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
Structural foam grade | Chemically blown thick-wall grade for large, stiff, low-density enclosures and pallets. | 32 | 32 | 5 | 110 HRR |
PPE-PPThis page PPE+PP alloy | Low-density, hydrolysis- and chemical-resistant alloy used for EV battery packs and photovoltaic hardware where light weight plus non-halogen FR matters. | 40 | 42 | 25 | 60 HRM |
Impact-modified | Rubber-boosted grade for thin-wall enclosures and parts needing cold-temperature drop resistance. | 46 | 46 | 70 | 65 HRM |
Mineral / talc filled | Low-warpage stiffening with isotropic shrinkage and good surface for painted or plated cosmetic parts. | 52 | 52 | 12 | 82 HRM |
Non-halogen flame-retardant, UL 94 V-0 | Phosphate-ester FR grade for enclosures, breakers, PV junction boxes and battery components requiring V-0 at 1.5 mm. | — | 55 | 40 | — |
PPE+PA alloy | Semi-crystalline nylon-continuous alloy chosen when solvent resistance and online-paint-bake temperature are needed (automotive fenders, EV connectors). | 55 | 58 | 45 | 70 HRM |
UNFDefault Unfilled / natural | Default choice for housings, water-contact parts and dielectric components needing toughness and dimensional stability. | 58 | 58 | 50 | 78 HRM |
ESD / static-dissipative | Carbon-black or carbon-fiber loaded mPPE for electronics trays, fuel-system and clean-handling parts. | 60 | 60 | 8 | 80 HRM |
10% glass-fiber reinforced | Light reinforcement when stiffness and creep resistance must improve but low warpage is still required. | — | 76 | 6 | — |
20% glass-fiber reinforced | Mid-range stiffness/temperature upgrade for pump housings and structural brackets. | — | 95 | 4 | — |
30% glass-fiber reinforced, flame-retardant V-0 | Structural + V-0 combination for EV battery frames, chargers and electrical switchgear. | — | 100 | 2.8 | 95 HRM |
30% glass-fiber reinforced | Highest stiffness and HDT of the standard mPPE range; pick for load-bearing housings and metal-replacement parts. | — | 112 | 3.5 | — |
What is mPPE PPE-PP?
mPPE PPE-PP is mPPE in the PPE-PP condition — low-density, hydrolysis- and chemical-resistant alloy used for EV battery packs and photovoltaic hardware where light weight plus non-halogen FR matters. mPPE PPE-PP has a yield strength of 40 MPa (5.8 ksi) and a tensile strength of 42 MPa (6.09 ksi) — weaker than 63% of polymer grades. Elongation at break is 25% and the elastic modulus is 1.8 GPa (0.261 Msi). mPPE PPE-PP has a density of 1.02 g/cm³ (0.0368 lb/in³), lighter than 72% of polymer grades. Its glass-transition temperature is 145°C (293 °F). UNF is the default condition FabDigit quotes; PPE-PP is available on request or by drawing note.
Advantages
- Tough — resists crack growth — 4 MPa·√m (3.64 ksi·√in), better than 92% of polymer grades
- Low moisture uptake — 0.07%, better than 81% of polymer grades
mPPE PPE-PP properties
Typical room-temperature values for mPPE PPE-PP; 29 are specific to this condition. Other listed values are mPPE reference data and may not represent this condition. Bars are the position among polymer grades.
Physical4
mPPE PPE-PP has a density of 1.02 g/cm³ (0.0368 lb/in³), lighter than 72% of polymer grades. Its glass-transition temperature is 145°C (293 °F).
Mechanical16
mPPE PPE-PP has a yield strength of 40 MPa (5.8 ksi) and a tensile strength of 42 MPa (6.09 ksi) — weaker than 63% of polymer grades. Elongation at break is 25% and the elastic modulus is 1.8 GPa (0.261 Msi).
Thermal11
mPPE PPE-PP is rated for continuous service to 95°C (203 °F). It conducts heat at 0.22 W/m·K (0.127 BTU/hr·ft·°F), better than 60% of polymer grades. Thermal expansion is 65 µm/m·K (36.1 µin/in·°F).
Electrical7
mPPE PPE-PP is an electrical insulator with a dielectric strength of 21 kV/mm (533.4 V/mil) and a resistivity of 1×10¹⁴ Ω·m.
Chemical & Environmental3
Corrosion resistance is excellent (88/100), better than 74% of polymer grades. UV resistance is fair.
Sustainability4
Producing a kilogram of mPPE PPE-PP takes about 110 MJ of energy and emits 4.6 kg of CO₂ — more than 64% of polymer grades. Typical recycled content is 5%.
Manufacturability8
mPPE PPE-PP's machinability is good (60/100, better than 51% of polymer grades); weldability good (55/100); formability fair (45/100).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with mPPE PPE-PP
Is mPPE easy to machine?
Machines cleanly with sharp positive-rake tools and air cooling; avoid aromatic/chlorinated coolants which cause stress cracking, and anneal 2 h at ~110 °C before tight-tolerance finishing.
Can mPPE be welded?
Excellent for ultrasonic, vibration and hot-plate welding; solvent bonding with chlorinated solvents or adhesives also works, but hot-gas welding needs careful temperature control to avoid PS-phase degradation.
Can mPPE be formed, bent or molded?
Dry 2–4 h at 100–110 °C, mold at 260–300 °C melt with 60–110 °C tool; amorphous shrinkage of ~0.5–0.7 % is low and isotropic, giving very stable tolerances.
What surface finishes work on mPPE?
Takes paint, hot stamping and electroless plating well after standard etch/primer steps; UV-absorbing paint or pigment is recommended for outdoor use since unstabilized mPPE yellows.
mPPE chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| poly(2,6-dimethyl-1,4-phenylene ether) (resin fraction sets Tg/HDT | 25 – 70 | 45 |
| impact modifier (SBS/SEBS rubber) | 0 – 10 | 3 |
| phosphate ester flame retardantFR grades only, non-halogen | 0 – 15 | 0 |
| glass fiberGF variants | 0 – 30 | 0 |
| stabilizers, pigments, mold release | 0.3 – 3 | 1 |
| high-impact polystyrene (HIPS/PS)flow and impact carrier phase | ≥ 25 (balance) | — |
mPPE PPE-PP — frequently asked
What is mPPE PPE-PP used for?
mPPE PPE-PP is typically used for electrical enclosures and connectors, automotive instrument panels, plumbing fittings, business machine housings and HVAC components. In short: most dimensionally stable amorphous resin; lowest-density engineering thermoplastic; inherently flame-retardant blend.
What is the yield strength of mPPE PPE-PP?
mPPE PPE-PP has a typical yield strength of 40 MPa (5.8 ksi) and a tensile strength of 42 MPa (6.09 ksi) — weaker than 63% of polymer grades. Strength varies by condition: see the 12 listed tempers.
Is mPPE PPE-PP easy to machine?
Reasonably — machinability is rated good (60/100, better than 51% of polymer grades). Machines cleanly with sharp positive-rake tools and air cooling; avoid aromatic/chlorinated coolants which cause stress cracking, and anneal 2 h at ~110 °C before tight-tolerance finishing.
Can mPPE PPE-PP be welded?
Yes — weldability is rated good (55/100). Excellent for ultrasonic, vibration and hot-plate welding; solvent bonding with chlorinated solvents or adhesives also works, but hot-gas welding needs careful temperature control to avoid PS-phase degradation.
What surface finishes work on mPPE PPE-PP?
Takes paint, hot stamping and electroless plating well after standard etch/primer steps; UV-absorbing paint or pigment is recommended for outdoor use since unstabilized mPPE yellows.
Can mPPE PPE-PP be formed, bent or molded?
Dry 2–4 h at 100–110 °C, mold at 260–300 °C melt with 60–110 °C tool; amorphous shrinkage of ~0.5–0.7 % is low and isotropic, giving very stable tolerances.
What is the maximum service temperature of mPPE PPE-PP?
mPPE PPE-PP is rated for continuous use to about 95°C (203 °F), and briefly to 130°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between mPPE UNF and mPPE SF?
UNF is the default condition — default choice for housings, water-contact parts and dielectric components needing toughness and dimensional stability. SF: chemically blown thick-wall grade for large, stiff, low-density enclosures and pallets. Yield strength is 58 MPa in UNF versus 32 MPa in SF.
Sources
- Noryl resin family datasheets (731, N190, GFN2/GFN3, PPX, GTX) — SABIC Specialties / SHPP (2023)
- CAMPUS plastics database — PPE+PS entries — CWFG / CAMPUS consortium (2024)
- Engineered Materials Handbook Vol. 2: Engineering Plastics — ASM International (1988)
- ISO 1043-1 / ISO 527 / ISO 75 / ISO 306 test methods for thermoplastics — ISO (2019)
- GB/T 15065 GB/T 1040 — SAC (2018)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.