EPS 150
EN 13163 EPS150
EPS 150 is a higher-strength EN 13163 expanded polystyrene grade rated at 150 kPa compressive strength, with nominal density 0.028 g/cm³ (28 kg/m³), thermal conductivity 0.033 W/m·K and tensile strength 0.3 MPa.
Reference datasheet — EPS 150 is not in the instant-quote catalog. Upload your part and an engineer will quote it in this grade or suggest the closest stocked equivalent.
Values for the STD-FR condition
EPS 150 grades and fills
EPS 150 is supplied in 5 conditions, soft to hard. STD-FR is the default FabDigit quotes; the values on this page are for it.
Compare all 5 grades and fillsHide
| Grade · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
STD-FRDefault Standard white flame-retarded EPS 150 board | Default construction board: CE-marked EN 13163 EPS150 with polymeric brominated FR, for roofs, floors and walls. | 0.15 | 0.3 | 2 | |
graphite/IR-absorber enhanced grey EPS 150 | Pick when the same 150 kPa strength is needed at 8–12 % lower λ or thinner build-up; grey boards need shading during installation. | 0.15 | 0.29 | 1.8 | |
Non-flame-retarded (packaging / industrial) EPS at 150 kPa strength | Cheaper FR-free beads for packaging, moulds, void formers and non-building uses where no fire class is required. | 0.15 | 0.3 | 2 | |
Lightweight fill block equivalent | Large sawn blocks for embankment fill, bridge approaches and load reduction over utilities, specified by compressive resistance at 1 % and 10 % strain. | 0.16 | 0.32 | 2 | |
perimeter / inverted-roof grade with reduced water uptake | Choose for below-grade and inverted-roof service: tighter fusion and grooved/skinned faces cut long-term water absorption and add drainage. | 0.17 | 0.33 | 2 |
What is EPS 150?
EPS 150 is a higher-strength EN 13163 expanded polystyrene grade rated at 150 kPa compressive strength, with nominal density 0.028 g/cm³ (28 kg/m³), thermal conductivity 0.033 W/m·K and tensile strength 0.3 MPa. It suits inverted roofs and moderate structural loads, and is supplied as flame-retardant board, grey graphite board, non-FR stock, perimeter board and geofoam blocks. Maximum service temperature is 80 °C, and the foam must be shielded from UV, solvents and hot bitumen. Choose EPS 100 for lighter floor loads or EPS 200 for heavy floors and geofoam fills. EPS 150 has a density of 0.03 g/cm³ (0.001 lb/in³), lighter than 96% of polymer grades. Its glass-transition temperature is 100°C (212 °F). EPS 150 has a yield strength of 0.15 MPa (0.0218 ksi) and a tensile strength of 0.3 MPa (0.0435 ksi) — weaker than 99% of polymer grades. Elongation at break is 2% and the elastic modulus is 0.01 GPa (0.0013 Msi).
What is EPS 150 used for?
- Inverted roof insulation
- Parking area and deck insulation
- Loaded floor insulation under screed
- Perimeter and below-slab edge insulation
- Geofoam lightweight fill blocks
- External wall insulation (ETICS) boards
- Cold store floor and wall panels
Advantages
- Lightweight — 0.03 g/cm³ (0.001 lb/in³), better than 96% of polymer grades
- Easy to machine — 88/100, better than 92% of polymer grades
- Low, predictable mold shrinkage — 0.4%, better than 82% of polymer grades
- Low embodied carbon — 3.3 kg CO₂/kg, better than 78% of polymer grades
Limitations
- Low strength — 0.15 MPa (0.0218 ksi), worse than 99% of polymer grades
- Degrades in UV without stabilisers — 12/100, worse than 99% of polymer grades
- Limited ductility — 2%, worse than 95% of polymer grades
- Poor heat conductor — 0.03 W/m·K (0.0191 BTU/hr·ft·°F), worse than 95% of polymer grades
- Needs corrosion protection — 58/100, worse than 92% of polymer grades
EPS 150 properties
Typical room-temperature values for EPS 150-STD-FR; bars are the position among polymer grades.
Physical4
EPS 150 has a density of 0.03 g/cm³ (0.001 lb/in³), lighter than 96% of polymer grades. Its glass-transition temperature is 100°C (212 °F).
Mechanical12
EPS 150 has a yield strength of 0.15 MPa (0.0218 ksi) and a tensile strength of 0.3 MPa (0.0435 ksi) — weaker than 99% of polymer grades. Elongation at break is 2% and the elastic modulus is 0.01 GPa (0.0013 Msi).
Thermal9
EPS 150 is rated for continuous service to 80°C (176 °F). It conducts heat at 0.03 W/m·K (0.0191 BTU/hr·ft·°F), worse than 95% of polymer grades. Thermal expansion is 65 µm/m·K (36.1 µin/in·°F).
Electrical4
EPS 150 has an electrical resistivity of 1×10¹³ Ω·m.
Chemical & Environmental3
Corrosion resistance is good (58/100), worse than 92% of polymer grades. UV resistance is not recommended.
Sustainability4
Producing a kilogram of EPS 150 takes about 95 MJ of energy and emits 3.3 kg of CO₂ — less than 70% of polymer grades. Typical recycled content is 5%.
Manufacturability5
EPS 150's machinability is excellent (88/100, better than 92% of polymer grades); weldability fair (40/100); formability poor (25/100).
Common Calculations5
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Strength versus weight in the polymer family
Yield strength against density for every polymer grade FabDigit runs. EPS 150 is highlighted; hover a dot for its name, or open the interactive family chart.
Working with EPS 150
Is EPS 150 easy to machine?
Cut with hot wire, hot knife or fine-tooth band saw; routing and CNC hot-wire shaping are easy but generate static-charged beads that need extraction.
Can EPS 150 be welded?
No true welding — blocks are fused in the steam mould; on site joints are butt/lap taped or bonded with solvent-free (water- or PU-based) adhesive, never solvent or hot bitumen.
Can EPS 150 be formed, bent or molded?
Pre-expand beads with steam, age in silos, then block- or shape-mould at ~105–125 °C steam; block density is set to hit the 150 kPa compressive class before sawing to boards.
EPS 150 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| pentane (residual blowing agent)decreases with ageing/conditioning of blocks | 0.2 – 2 | 1 |
| polymeric brominated flame retardant (PoHBCD replaced since 2015; absent in NON-FR variant | 0.4 – 1.5 | 0.8 |
| graphite (IR absorber)GRAPHITE variant only | 0 – 4 | 2.5 |
| processing additives (nucleant, antistat | 0.05 – 0.5 | 0.2 |
| polystyrene (styrene homopolymer)solid polymer skeleton; foam is >95 vol % air | ≥ 94 (balance) |
What surface finishes work on EPS 150?
Faces take cement- or polymer-modified renders, EIFS/ETICS mesh coats, gypsum boards and factory-laminated facings; must be shielded from UV, solvents and temperatures above ~80 °C.
Equivalent designations
Standards and trade names that resolve to EPS 150 in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- EN / DIN / Werkstoff-Nr.
- 13163 EPS150
How much does EPS 150 cost?
EPS 150 is a standard-cost polymer ($$), cheaper than about 71% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
EPS 150 — frequently asked
What is EPS 150 used for?
EPS 150 is typically used for inverted roof insulation, parking area and deck insulation, loaded floor insulation under screed, perimeter and below-slab edge insulation, geofoam lightweight fill blocks and external wall insulation (ETICS) boards. In short: 150 kPa structural EPS class; lower lambda than EPS 100; geofoam-capable strength.
What is the yield strength of EPS 150?
EPS 150 has a typical yield strength of 0.15 MPa (0.0218 ksi) and a tensile strength of 0.3 MPa (0.0435 ksi) — weaker than 99% of polymer grades. Strength varies by condition: see the 5 listed tempers.
Is EPS 150 easy to machine?
Yes — machinability is rated excellent (88/100, better than 92% of polymer grades). Cut with hot wire, hot knife or fine-tooth band saw; routing and CNC hot-wire shaping are easy but generate static-charged beads that need extraction.
Can EPS 150 be welded?
With care — weldability is rated fair (40/100). No true welding — blocks are fused in the steam mould; on site joints are butt/lap taped or bonded with solvent-free (water- or PU-based) adhesive, never solvent or hot bitumen.
What surface finishes work on EPS 150?
Faces take cement- or polymer-modified renders, EIFS/ETICS mesh coats, gypsum boards and factory-laminated facings; must be shielded from UV, solvents and temperatures above ~80 °C.
Can EPS 150 be formed, bent or molded?
Pre-expand beads with steam, age in silos, then block- or shape-mould at ~105–125 °C steam; block density is set to hit the 150 kPa compressive class before sawing to boards.
What is the maximum service temperature of EPS 150?
EPS 150 is rated for continuous use to about 80°C (176 °F), and briefly to 100°C. Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between EPS 150 STD-FR and EPS 150 GEOFOAM?
STD-FR is the default condition — default construction board: CE-marked EN 13163 EPS150 with polymeric brominated FR, for roofs, floors and walls. GEOFOAM: large sawn blocks for embankment fill, bridge approaches and load reduction over utilities, specified by compressive resistance at 1 % and 10 % strain. Yield strength is 0.15 MPa in STD-FR versus 0.16 MPa in GEOFOAM.
How much does EPS 150 cost?
EPS 150 is a standard-cost polymer ($$), cheaper than about 71% of the materials FabDigit quotes. Part price depends far more on geometry, tolerance and quantity than on the raw stock — upload a CAD file for a live quote.
Sources
- EN 13163 — Thermal insulation products for buildings: factory made expanded polystyrene (EPS) — CEN (2016)
- EN 14933 — Lightweight fill and thermal insulation products for civil engineering: EPS — CEN (2007)
- ASTM D6817 / ASTM C578 — Rigid cellular polystyrene geofoam and thermal insulation — ASTM (2021)
- Styropor / Neopor technical information (physical and mechanical property tables) — BASF (2020)
- EUMEPS EPS property and EPD compilations — EUMEPS (2022)
- ICE Inventory of Carbon & Energy v3 (EPS insulation) — Circular Ecology (2019)
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.