Copper Alloy C70600 vs C79600
Copper Alloy · grade comparison
Copper Alloy C70600 and C79600 are both copper alloy grades. C79600 is the stronger of the two: yield strength 400 MPa (58 ksi) against 120 MPa (17.4 ksi) for C70600, about 3.3 times as much; tensile strength follows at 550 MPa (79.8 ksi) vs 310 MPa (45 ksi). In exchange, C70600 is the more ductile: elongation 40% versus 15% for C79600, and C79600 is harder (160 HB vs 65 HB). C79600 is lighter (8.52 g/cm³ vs 8.94 g/cm³ for C70600) and C70600 is stiffer (124 GPa vs 117 GPa). On the shop floor, C79600 machines more easily (very good vs poor) and C70600 welds better (excellent vs poor).
C70600Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
C79600Choose it when strength drives the design, or when weight is the constraint.
C70600 vs C79600: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Same in both: Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | C70600 | C79600 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 4 finishes: Copper Plating, Electroless Nickel (EN), Gold Plating, Silver Plating.
C70600 vs C79600 — frequently asked
Is C79600 stronger than C70600?
Yes. C79600 has a typical yield strength of 400 MPa (58 ksi) against 120 MPa (17.4 ksi) for C70600 — about 3.3 times as much. Tensile strength is 550 MPa (79.8 ksi) vs 310 MPa (45 ksi).
Which is cheaper, C70600 or C79600?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, C70600 or C79600?
C79600. Its machinability rates very good (72/100) against poor (28/100) for C70600; for welding the order is C70600 first (excellent, 92/100) then C79600 (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in C70600 and C79600 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.