PA6 vs Vero
Polymer · grade comparison
PA6 and Vero are both polymer grades, both engineering plastic. PA6 is the stronger of the two: tensile strength 80 MPa (11.6 ksi) against 57 MPa (8.27 ksi) for Vero, about 40% more. PA6 is the more ductile: elongation 60% versus 17% for Vero. PA6 is stiffer (3 GPa vs 2.5 GPa) and PA6 runs hotter in service (90°C vs 45°C continuous). On the shop floor, PA6 machines more easily (68 vs 55 out of 100), PA6 welds better (good vs not recommended), and PA6 sits in a lower cost tier (budget, $) than Vero (specialty, $$$$$).
PA6Choose it when strength drives the design, or when the part is bent, formed or impact-loaded.
PA6 vs Vero: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Compressive Modulus
Flexural Strength
Flexural Modulus
Shear Strength
Fracture Toughness (K_IC)
Izod Impact, Notched
Hardness, Shore D
Hardness, Rockwell M
Hardness, Rockwell R
Physical
Density and transition temperatures.
Density
Melting Temperature (Tm)
Glass Transition (Tg)
Water Absorption (24 h)
Water Absorption (Saturation)
Refractive Index
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Vicat Softening Point (B50)
Limiting Oxygen Index
Max Service Temperature (short-term)
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Strength
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Volume Resistivity
Surface Resistivity
Comparative Tracking Index (CTI)
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Polishability
Mold Shrinkage
Melt Flow Rate
Processing Melt Temperature (typ.)
Mold Temperature (typ.)
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | PA6 | Vero |
|---|---|---|
| CNC machining | Yes | — |
| Sheet metal | Yes | — |
| Injection molding | Yes | — |
| 3D printing | — | Yes |
| Default condition | Unfilled | Vivid Colors |
| Relative cost | $ Budget | $$$$$ Specialty |
| Min. machined wall | 0.5 mm | — |
| Best machined surface | Ra 0.8 µm | — |
| Chrome Plating (Plastic) | Yes | — |
| Conductive Coating | — | Yes |
| Dyeing (Nylon) | — | Yes |
| Primer Coating | — | Yes |
| Spray Painting | Yes | — |
| Tinted Coating | — | Yes |
| Vacuum Metallization | — | Yes |
| Waterproof Coating | — | Yes |
They share 4 finishes: EMI Shielding Coating, Painting, Soft Touch Coating, UV Coating.
PA6 vs Vero — frequently asked
Is PA6 stronger than Vero?
Yes. PA6 has a typical tensile strength of 80 MPa (11.6 ksi) against 57 MPa (8.27 ksi) for Vero — about 40% more.
Which is cheaper, PA6 or Vero?
PA6 is the lower-cost material: it sits in the budget tier ($) while Vero is specialty ($$$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, PA6 or Vero?
PA6, by a small margin. Both rate good for machinability — 68/100 against 55/100 for Vero; for welding the order is PA6 first (good, 62/100) then Vero (not recommended, 5/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in PA6 and Vero side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.