YN05 HIP (Hot isostatic pressed)
Print state
Pick sinter-HIP densification after sintering to remove residual porosity when transverse rupture strength and edge chipping resistance must rise for light interrupted finishing.
Values for the HIP condition
Other YN05 tempers and conditions
YN05 is listed in 2 conditions; see the grade overview at YN05.
- HIP
- UF
Compare all 2 conditionsHide
| Condition · open for datasheet | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness | Conductivity |
|---|---|---|---|---|---|---|
HIPThis page Hot isostatic pressed | Pick sinter-HIP densification after sintering to remove residual porosity when transverse rupture strength and edge chipping resistance must rise for light interrupted finishing. | — | 620 | 0.1 | 1,830 HV | 23 W/m·K |
Ultra-fine grain (<0.8 µm) TiCN-based cermet | Choose the ultra-fine grain (<0.8 µm) TiCN-based structure for the sharpest edge and mirror surface quality in ultra-precision turning and mill-instead-of-grind work. | — | — | — | 1,900 HV | 20 W/m·K |
What is YN05 HIP?
YN05 HIP is YN05 in the HIP condition — pick sinter-HIP densification after sintering to remove residual porosity when transverse rupture strength and edge chipping resistance must rise for light interrupted finishing. The elastic modulus is 415 GPa (60.2 Msi). YN05 HIP has a density of 6.05 g/cm³ (0.219 lb/in³), heavier than 66% of ceramic grades. It melts at 1,280°C (2,336 °F).
Advantages
- Polishes to a fine finish — 92/100, better than 89% of ceramic grades
YN05 HIP properties
Typical room-temperature values for YN05 HIP; 15 are specific to this condition. Other listed values are YN05 reference data and may not represent this condition. Bars are the position among ceramic grades.
Physical3
YN05 HIP has a density of 6.05 g/cm³ (0.219 lb/in³), heavier than 66% of ceramic grades. It melts at 1,280°C (2,336 °F).
Mechanical10
The elastic modulus is 415 GPa (60.2 Msi).
Thermal5
YN05 HIP is rated for continuous service to 1,000°C (1,832 °F). It conducts heat at 23 W/m·K (13.3 BTU/hr·ft·°F), better than 52% of ceramic grades. Thermal expansion is 7.4 µm/m·K (4.11 µin/in·°F).
Electrical1
YN05 HIP has an electrical resistivity of 7.5×10⁻⁷ Ω·m.
Chemical & Environmental2
Corrosion resistance is very good (72/100), worse than 53% of ceramic grades.
Sustainability3
Producing a kilogram of YN05 HIP takes about 210 MJ of energy and emits 15 kg of CO₂ — more than 64% of ceramic grades. Typical recycled content is 5%.
Manufacturability3
YN05 HIP's machinability is not recommended (4/100, worse than 85% of ceramic grades).
Values are nominal handbook figures for design screening. Confirm any required mill or lot documentation when quoting.
Working with YN05 HIP
Is YN05 easy to machine?
After sintering, only diamond-wheel grinding, EDM (conductive) or laser processing is possible; green blanks can be turned or milled before sintering.
Can YN05 be welded?
Not fusion weldable. Braze tips to steel bodies with silver-based (BAg) filler in vacuum or by induction and control the cooling rate closely, as CTE mismatch makes it more crack-sensitive than WC-based grades.
Can YN05 be formed, bent or molded?
Powder metallurgy: wet milling, spray drying, die pressing, extrusion or injection moulding, debinding, then vacuum or sinter-HIP densification at 1400-1470 °C.
What surface finishes work on YN05?
Diamond grinding plus polishing gives a mirror surface below Ra 0.05 µm. Precision edge preparation (T-land or honing) is required, and PVD TiN or TiAlN coatings can be added.
YN05 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Moadded as Mo or Mo2C; improves binder-phase wetting | 10 – 16 | 14.5 |
| Nimain binder phase | 4 – 8 | 5.5 |
| Copartly replaces Ni in some manufacturers' grades | 0 – 3 | 0.5 |
| TiCminor TiN/TiCN + WC solid solution; ultrafine grades Ti(C,N)-based | ≥ 70 (balance) | — |
YN05 HIP — frequently asked
What is YN05 HIP used for?
YN05 HIP is typically used for ultra-precision steel finishing, high-speed light cutting and fine surface finishing inserts. In short: ultra-fine cermet grade; best surface finish on steel; light finishing cuts only.
Is YN05 HIP easy to machine?
Not especially — machinability is rated not recommended (4/100, worse than 85% of ceramic grades). After sintering, only diamond-wheel grinding, EDM (conductive) or laser processing is possible; green blanks can be turned or milled before sintering.
Can YN05 HIP be welded?
Not fusion weldable. Braze tips to steel bodies with silver-based (BAg) filler in vacuum or by induction and control the cooling rate closely, as CTE mismatch makes it more crack-sensitive than WC-based grades.
What surface finishes work on YN05 HIP?
Diamond grinding plus polishing gives a mirror surface below Ra 0.05 µm. Precision edge preparation (T-land or honing) is required, and PVD TiN or TiAlN coatings can be added.
Can YN05 HIP be formed, bent or molded?
Powder metallurgy: wet milling, spray drying, die pressing, extrusion or injection moulding, debinding, then vacuum or sinter-HIP densification at 1400-1470 °C.
What is the maximum service temperature of YN05 HIP?
YN05 HIP is rated for continuous use to about 1,000°C (1,832 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Sources
- ASM Handbook Vol.2 — Properties of Cemented Carbides and Cermets — ASM International (1990)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.