Aluminum 3104 · temper
Aluminum 3104-H22
Properties of the H22 condition, compared with the other 3104 tempers.
Quarter-hard 3104 sheet cold rolled then back-annealed for a stable, more ductile temper used in deep-drawn bodies and formed closures.
What is 3104-H22?
3104-H22 is 3104 in the H22 temper — quarter-hard 3104 sheet cold rolled then back-annealed for a stable, more ductile temper used in deep-drawn bodies and formed closures. 3104-H22 has a yield strength of 170 MPa (24.7 ksi) and a tensile strength of 205 MPa (29.7 ksi) — weaker than 57% of aluminum grades. Elongation at break is 10% and the elastic modulus is 69 GPa (10 Msi). 3104-H22 has a density of 2.72 g/cm³ (0.0983 lb/in³), heavier than 57% of aluminum grades. It melts at 629°C (1,164 °F).
Advantages
- Forms and bends easily — 70/100, better than 83% of aluminum grades
- Good corrosion resistance — 70/100, better than 79% of aluminum grades
- High electrical conductivity — 41 % IACS, better than 78% of aluminum grades
- Conducts heat well — 160 W/m·K (92.4 BTU/hr·ft·°F), better than 75% of aluminum grades
Limitations
- Difficult to machine — 42/100, worse than 77% of aluminum grades
3104-H22 properties
Typical room-temperature values for 3104-H22 — 36 properties are specific to this condition; the rest are grade-level values shared by every 3104 temper. Each bar shows where the value sits among the aluminum grades in FabDigit's library — further right is higher.
Physical3
3104-H22 has a density of 2.72 g/cm³ (0.0983 lb/in³), heavier than 57% of aluminum grades. It melts at 629°C (1,164 °F).
Mechanical11
3104-H22 has a yield strength of 170 MPa (24.7 ksi) and a tensile strength of 205 MPa (29.7 ksi) — weaker than 57% of aluminum grades. Elongation at break is 10% and the elastic modulus is 69 GPa (10 Msi).
Thermal6
3104-H22 is rated for continuous service to 150°C (302 °F). It conducts heat at 160 W/m·K (92.4 BTU/hr·ft·°F), better than 75% of aluminum grades. Thermal expansion is 23.6 µm/m·K (13.1 µin/in·°F).
Electrical3
3104-H22 conducts electricity at 41 % IACS, better than 78% of aluminum grades.
Chemical & Environmental3
Corrosion resistance is very good (70/100), better than 79% of aluminum grades.
Sustainability4
Producing a kilogram of 3104-H22 takes about 200 MJ of energy and emits 12 kg of CO₂ — less than 60% of aluminum grades. Typical recycled content is 65%.
Manufacturability8
3104-H22's machinability is fair (42/100, worse than 77% of aluminum grades); weldability very good (78/100); formability very good (70/100).
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Other 3104 tempers and conditions
3104 is also supplied in 20 other conditions. The full side-by-side table is on the 3104 overview.
- H19The standard beverage-can body-stock temper: highest as-rolled strength with just enough ductility for draw-and-wall-iron.275 MPa yield · 82 HB
- H29Extra-hard partially annealed 3104 strip, close to H19 strength but with slightly better residual ductility for high-speed can-body and end stock.260 MPa yield · 80 HB
- H22Quarter-hard 3104 sheet cold rolled then back-annealed for a stable, more ductile temper used in deep-drawn bodies and formed closures.170 MPa yield · 58 HB
- OPick for maximum drawability and deep-forming before a later work-hardening step.70 MPa yield · 45 HB
Working with 3104-H22
Is 3104 easy to machine?
Soft and gummy — use sharp polished-flute carbide, high rake, high speed and flood lubricant to avoid built-up edge; chip breaking is poor.
Can 3104 be welded?
Readily GTAW/GMAW welded with 4043 or 5356 filler and resistance-welded; the strain-hardened HAZ softens back toward O-temper strength.
Can 3104 be formed, bent or molded?
In O/H2x tempers it deep-draws superbly; H19 coil is engineered for draw-and-wall-ironing of can bodies with controlled earing (<3 %) — avoid tight bends across the rolling direction.
What surface finishes work on 3104?
Normally lacquered or coil-coated after chromate-free conversion pretreatment; anodizes protectively but with a grey/brown tone, and it takes paints and printing inks well.
3104 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| Si | ≤ 0.6 | 0.25 |
| Fe | ≤ 0.8 | 0.45 |
| Cu | 0.05 – 0.25 | 0.15 |
| Mn | 0.8 – 1.4 | 1 |
| Mg | 0.8 – 1.3 | 1.1 |
| Zn | ≤ 0.25 | — |
| Ga | ≤ 0.05 | — |
| V | ≤ 0.05 | — |
| Ti | ≤ 0.1 | — |
| Others (each)each | ≤ 0.05 | — |
| Others (total)total | ≤ 0.15 | — |
| Al | balance | — |
3104-H22 — frequently asked
What is 3104-H22 used for?
3104-H22 is typically used for beverage can bodies, can cap and closure stock, draw-and-ironed containers, aerosol containers, coil-coated container stock and deep-drawn housings. In short: can body sheet; beverage industry.
What is the yield strength of 3104-H22?
3104-H22 has a typical yield strength of 170 MPa (24.7 ksi) and a tensile strength of 205 MPa (29.7 ksi) — weaker than 57% of aluminum grades. Strength varies by condition: see the 21 listed tempers.
Is 3104-H22 easy to machine?
Not especially — machinability is rated fair (42/100, worse than 77% of aluminum grades). Soft and gummy — use sharp polished-flute carbide, high rake, high speed and flood lubricant to avoid built-up edge; chip breaking is poor.
Can 3104-H22 be welded?
Yes — weldability is rated very good (78/100). Readily GTAW/GMAW welded with 4043 or 5356 filler and resistance-welded; the strain-hardened HAZ softens back toward O-temper strength.
What surface finishes work on 3104-H22?
Normally lacquered or coil-coated after chromate-free conversion pretreatment; anodizes protectively but with a grey/brown tone, and it takes paints and printing inks well.
Can 3104-H22 be formed, bent or molded?
In O/H2x tempers it deep-draws superbly; H19 coil is engineered for draw-and-wall-ironing of can bodies with controlled earing (<3 %) — avoid tight bends across the rolling direction.
What is the maximum service temperature of 3104-H22?
3104-H22 is rated for continuous use to about 150°C (302 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
Can FabDigit make parts in 3104-H22?
Yes — 3104-H22 is available for sheet metal with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- International Alloy Designations and Chemical Composition Limits for Wrought Aluminum (Teal Sheets) — The Aluminum Association (2018)
- EN 573-3 Aluminium and aluminium alloys — Chemical composition — CEN (2019)
- ASTM B209 / B209M Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate — ASTM International (2021)
- ASM Handbook Vol. 2 — Properties and Selection: Nonferrous Alloys (3004/3104 data) — ASM International (1990)
- ASM Handbook Vol. 13B — Corrosion: Materials — ASM International (2005)
- Beverage can body stock (3104-H19) coil datasheets — Novelis / Constellium (2023)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.