Steel A47 32510 vs A47 M3210
Steel · grade comparison
Steel A47 32510 and A47 M3210 are both steel grades. Both yield at about 240 MPa — strength does not separate them. A47 M3210 is the more ductile: elongation 14% versus 12% for A47 32510. On the shop floor, A47 32510 sits in a lower cost tier (budget, $) than A47 M3210 (standard, $$).
A47 32510Choose it when cost is the deciding factor.
A47 M3210Choose it when the part is bent, formed or impact-loaded.
A47 32510 vs A47 M3210: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Bulk Modulus
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 170 GPa24.7 Msi · Shear Modulus 66 GPa9.6 Msi · Poisson's Ratio 0.26 · Tensile Strength (Ultimate) 360 MPa52.2 ksi · Yield Strength (0.2% offset) 240 MPa34.8 ksi · Fracture Toughness (K_IC) 45 MPa·√m41 ksi·√in · Hardness, Brinell 130 HB
Physical
Density and transition temperatures.
Melting Point (Solidus)
Liquidus Temperature
Same in both: Density 7.3 g/cm³0.26 lb/in³
Thermal
How each material carries heat and how hot it can run.
Min Service Temperature
Same in both: Thermal Conductivity 51 W/m·K29.5 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 220 J/g94.6 BTU/lb · Max Service Temperature (continuous) 425°C797 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Same in both: Machinability Rating (AISI 1212 = 100 %) 120% · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 85%
Common Calculations
Ratios derived from the values above.
Same in both: Specific Strength (UTS / density) 49 kN·m/kg · Specific Stiffness (E / density) 23.3 MN·m/kg · Modulus of Resilience 169 kJ/m³ · Thermal Diffusivity 14 mm²/s · Thermal Shock Resistance Index 9
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | A47 32510 | A47 M3210 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $ Budget | $$ Standard |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 9 finishes: Copper Plating, Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Manganese Phosphate, Plasma Spray, Silver Plating, Zinc Phosphate.
A47 32510 vs A47 M3210 — frequently asked
What is the difference between A47 32510 and A47 M3210?
Steel A47 32510 and A47 M3210 are both steel grades. Both yield at about 240 MPa — strength does not separate them. A47 M3210 is the more ductile: elongation 14% versus 12% for A47 32510.
Which is cheaper, A47 32510 or A47 M3210?
A47 32510 is the lower-cost material: it sits in the budget tier ($) while A47 M3210 is standard ($$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, A47 32510 or A47 M3210?
A47 32510. Its machinability rates excellent (85/100) against very good (80/100) for A47 M3210.
Ready to make it?
Upload a CAD file and FabDigit prices the part in A47 32510 and A47 M3210 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.