Stainless Steel ER308H vs ER410NiMo
Stainless Steel · grade comparison
Stainless Steel ER308H and ER410NiMo are both stainless steel grades. ER410NiMo is the stronger of the two: yield strength 830 MPa (120 ksi) against 415 MPa (60.2 ksi) for ER308H, about 100% more; tensile strength follows at 950 MPa (138 ksi) vs 590 MPa (85.6 ksi). In exchange, ER308H is the more ductile: elongation 38% versus 14% for ER410NiMo, and ER410NiMo is harder (355 HB vs 175 HB). ER308H runs hotter in service (800°C vs 400°C continuous) and ER410NiMo conducts heat better (25 W/m·K vs 16.2 W/m·K). On the shop floor, ER308H machines more easily (fair vs poor) and ER308H welds better (excellent vs good).
ER308HChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
ER410NiMoChoose it when strength drives the design.
ER308H vs ER410NiMo: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Hardness, Rockwell C
Same in both: Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Same in both: Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Water
Typical Recycled Content
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 4.5 kg CO₂/kg
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | ER308H | ER410NiMo |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$ Premium | $$$ Premium |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 7 finishes: Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Pickling, Plasma Spray, Silver Plating.
ER308H vs ER410NiMo — frequently asked
Is ER410NiMo stronger than ER308H?
Yes. ER410NiMo has a typical yield strength of 830 MPa (120 ksi) against 415 MPa (60.2 ksi) for ER308H — about 100% more. Tensile strength is 950 MPa (138 ksi) vs 590 MPa (85.6 ksi).
Which is cheaper, ER308H or ER410NiMo?
Both sit in the same relative cost tier ($$$, premium); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, ER308H or ER410NiMo?
ER308H. Its machinability rates fair (38/100) against poor (22/100) for ER410NiMo; for welding the order is ER308H first (excellent, 88/100) then ER410NiMo (good, 65/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in ER308H and ER410NiMo side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.