Digital ABS vs VisiJet M2 ENT
Polymer · grade comparison
Digital ABS and VisiJet M2 ENT are both polymer grades. Digital ABS is the stronger of the two: tensile strength 57 MPa (8.27 ksi) against 42 MPa (6.09 ksi) for VisiJet M2 ENT, about 36% more. Digital ABS is the more ductile: elongation 30% versus 10% for VisiJet M2 ENT, and Digital ABS is harder (86 Shore D vs 80 Shore D). Digital ABS is stiffer (2.8 GPa vs 1.5 GPa) and Digital ABS runs hotter in service (50°C vs 40°C continuous). On the shop floor, Digital ABS welds better (poor vs not recommended) and VisiJet M2 ENT sits in a lower cost tier (high, $$$$) than Digital ABS (specialty, $$$$$).
Digital ABSChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
VisiJet M2 ENTChoose it when cost is the deciding factor.
Digital ABS vs VisiJet M2 ENT: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Shore D
Hardness, Rockwell M
Yield Strength (0.2% offset)
Compressive Strength
Shear Strength
Fracture Toughness (K_IC)
Hardness, Shore A
Hardness, Rockwell R
Same in both: Poisson's Ratio 0.38
Physical
Density and transition temperatures.
Density
Glass Transition (Tg)
Water Absorption (24 h)
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Heat Deflection Temp. @ 0.45 MPa
Heat Deflection Temp. @ 1.8 MPa
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Vicat Softening Point (B50)
Limiting Oxygen Index
Same in both: Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Constant (1 MHz)
Volume Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Polishability
Formability (cold)
Mold Shrinkage
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Digital ABS | VisiJet M2 ENT |
|---|---|---|
| 3D printing | Yes | — |
| Default condition | Standard | — |
| Relative cost | $$$$$ Specialty | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
| Conductive Coating | Yes | — |
| Dyeing (Nylon) | Yes | — |
| EMI Shielding Coating | Yes | — |
| Painting | Yes | — |
| Primer Coating | Yes | — |
| Soft Touch Coating | Yes | — |
| Tinted Coating | Yes | — |
| UV Coating | Yes | — |
| Vacuum Metallization | Yes | — |
| Waterproof Coating | Yes | — |
Digital ABS vs VisiJet M2 ENT — frequently asked
Is Digital ABS stronger than VisiJet M2 ENT?
Yes. Digital ABS has a typical tensile strength of 57 MPa (8.27 ksi) against 42 MPa (6.09 ksi) for VisiJet M2 ENT — about 36% more.
Which is cheaper, Digital ABS or VisiJet M2 ENT?
VisiJet M2 ENT is the lower-cost material: it sits in the high tier ($$$$) while Digital ABS is specialty ($$$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, Digital ABS or VisiJet M2 ENT?
Digital ABS. Its machinability rates good (55/100) against fair (50/100) for VisiJet M2 ENT; for welding the order is Digital ABS first (poor, 15/100) then VisiJet M2 ENT (not recommended, 0/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Digital ABS and VisiJet M2 ENT side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.