Nickel 201 vs Nickel 211
Nickel Alloy · grade comparison
Nickel 201 and Nickel 211 are both nickel alloy grades. Nickel 211 is the stronger of the two: yield strength 210 MPa (30.5 ksi) against 105 MPa (15.2 ksi) for Nickel 201, about 100% more; tensile strength follows at 480 MPa (69.6 ksi) vs 415 MPa (60.2 ksi). In exchange, Nickel 201 is the more ductile: elongation 47% versus 40% for Nickel 211, and Nickel 211 is harder (110 HB vs 90 HB). Nickel 201 runs hotter in service (650°C vs 315°C continuous) and Nickel 201 conducts heat better (79 W/m·K vs 42 W/m·K). On the shop floor, Nickel 201 welds better (excellent vs very good).
Nickel 201Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Nickel 211Choose it when strength drives the design.
Nickel 201 vs Nickel 211: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Shear Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Bulk Modulus 180 GPa26.1 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Specific Heat Capacity 456 J/kg·K0.11 BTU/lb·°F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Same in both: Machinability 30 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 30%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Nickel 201 | Nickel 211 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
Nickel 201 vs Nickel 211 — frequently asked
Is Nickel 211 stronger than Nickel 201?
Yes. Nickel 211 has a typical yield strength of 210 MPa (30.5 ksi) against 105 MPa (15.2 ksi) for Nickel 201 — about 100% more. Tensile strength is 480 MPa (69.6 ksi) vs 415 MPa (60.2 ksi).
Which is cheaper, Nickel 201 or Nickel 211?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, Nickel 201 or Nickel 211?
Nickel 201. Its weldability rates excellent (85/100) against very good (72/100) for Nickel 211.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Nickel 201 and Nickel 211 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.