Nickel Alloy Hastelloy X vs N06250
Nickel Alloy · grade comparison
Nickel Alloy Hastelloy X and N06250 are both nickel alloy grades. Both yield at about 360 MPa — strength does not separate them. N06250 is the more ductile: elongation 58% versus 43% for Hastelloy X, and Hastelloy X is harder (195 HB vs 180 HB). Hastelloy X is lighter (8.22 g/cm³ vs 8.7 g/cm³ for N06250) and Hastelloy X runs hotter in service (1,150°C vs 650°C continuous). On the shop floor, Hastelloy X sits in a lower cost tier (premium, $$$) than N06250 (high, $$$$).
Hastelloy XChoose it when weight is the constraint, or when the part sees heat.
N06250Choose it when the part is bent, formed or impact-loaded.
Hastelloy X vs N06250: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Reduction in Area
Compressive Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Hardness, Rockwell C
Same in both: Shear Modulus 79 GPa11.5 Msi · Yield Strength (0.2% offset) 360 MPa52.2 ksi · Shear Strength 490 MPa71.1 ksi
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Same in both: Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Castability
Brazeability / Solderability
Polishability
Same in both: Machinability 18 / 100 · Machinability Rating (AISI 1212 = 100 %) 12% · Weldability 85 / 100 · Formability (cold) 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Hastelloy X | N06250 |
|---|---|---|
| CNC machining | Yes | — |
| Sheet metal | Yes | — |
| 3D printing | Yes | — |
| Default condition | Solution Annealed | — |
| Relative cost | $$$ Premium | $$$$ High |
| Min. machined wall | 1.5 mm | — |
| Best machined surface | Ra 1.6 µm | — |
| Electropolishing | Yes | — |
| HVOF Coating | Yes | — |
They share 3 finishes: Gold Plating, Plasma Spray, Silver Plating.
Hastelloy X vs N06250 — frequently asked
What is the difference between Hastelloy X and N06250?
Nickel Alloy Hastelloy X and N06250 are both nickel alloy grades. Both yield at about 360 MPa — strength does not separate them. N06250 is the more ductile: elongation 58% versus 43% for Hastelloy X, and Hastelloy X is harder (195 HB vs 180 HB).
Which is cheaper, Hastelloy X or N06250?
Hastelloy X is the lower-cost material: it sits in the premium tier ($$$) while N06250 is high ($$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
When should I choose Hastelloy X over N06250?
Pick Hastelloy X when weight is the constraint, or when the part sees heat. Pick N06250 when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Hastelloy X and N06250 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.