Mycalex vs Neoceram
Glass · grade comparison
Mycalex and Neoceram are both glass grades. Neoceram is the stronger of the two: tensile strength 50 MPa (7.25 ksi) against 45 MPa (6.53 ksi) for Mycalex, about 11% more. In exchange, Mycalex is the more ductile: elongation 0.1% versus 0% for Neoceram, and Neoceram is harder (700 HV vs 250 HV). Neoceram is lighter (2.51 g/cm³ vs 3.4 g/cm³ for Mycalex) and Neoceram is stiffer (88 GPa vs 65 GPa). On the shop floor, Mycalex machines more easily (very good vs not recommended).
MycalexChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
NeoceramChoose it when strength drives the design, or when weight is the constraint.
Mycalex vs Neoceram: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all glass grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all glass grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Flexural Strength
Shear Strength
Fracture Toughness (K_IC)
Hardness, Vickers
Hardness, Knoop
Hardness, Mohs
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Refractive Index
Light Transmission
Same in both: Porosity 0%
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Same in both: Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Strength
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Volume Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sintering / Firing Temperature
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 5%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every glass grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Mycalex | Neoceram |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Mycalex vs Neoceram — frequently asked
Is Neoceram stronger than Mycalex?
Yes. Neoceram has a typical tensile strength of 50 MPa (7.25 ksi) against 45 MPa (6.53 ksi) for Mycalex — about 11% more.
Which is cheaper, Mycalex or Neoceram?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, Mycalex or Neoceram?
Mycalex. Its machinability rates very good (75/100) against not recommended (8/100) for Neoceram.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Mycalex and Neoceram side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.