3021 vs G-3
Composite · grade comparison
3021 and G-3 are both composite grades. G-3 is the stronger of the two: tensile strength 250 MPa (36.3 ksi) against 90 MPa (13.1 ksi) for 3021, about 178% more. 3021 is lighter (1.4 g/cm³ vs 1.85 g/cm³ for G-3) and G-3 is stiffer (18 GPa vs 8 GPa). On the shop floor, 3021 machines more easily (very good vs fair) and 3021 sits in a lower cost tier (standard, $$) than G-3 (premium, $$$).
3021Choose it when weight is the constraint, or when the part is machined in volume.
G-3Choose it when strength drives the design.
3021 vs G-3: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Compressive Strength
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Hardness, Rockwell M
Shear Modulus
Compressive Modulus
Shear Strength
Same in both: Elongation at Break 1.5%
Physical
Density and transition temperatures.
Density
Glass Transition (Tg)
Water Absorption (24 h)
Water Absorption (Saturation)
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Heat Deflection Temp. @ 1.8 MPa
Limiting Oxygen Index
Max Service Temperature (short-term)
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Strength
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Volume Resistivity
Same in both: Surface Resistivity 1×10¹¹ Ω · Comparative Tracking Index (CTI) 125 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Diffusivity 0.1 mm²/s · Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 3021 | G-3 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$ Standard | $$$ Premium |
| Min. machined wall | — | — |
| Best machined surface | — | — |
3021 vs G-3 — frequently asked
Is G-3 stronger than 3021?
Yes. G-3 has a typical tensile strength of 250 MPa (36.3 ksi) against 90 MPa (13.1 ksi) for 3021 — about 178% more.
Which is cheaper, 3021 or G-3?
3021 is the lower-cost material: it sits in the standard tier ($$) while G-3 is premium ($$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, 3021 or G-3?
3021. Its machinability rates very good (80/100) against fair (42/100) for G-3.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 3021 and G-3 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.