Titanium Grade 1 vs Ti-6242
Titanium · grade comparison
Titanium Grade 1 and Ti-6242 are both titanium grades. Ti-6242 is the stronger of the two: yield strength 930 MPa (135 ksi) against 220 MPa (31.9 ksi) for Grade 1, about 4.2 times as much; tensile strength follows at 1,000 MPa (145 ksi) vs 300 MPa (43.5 ksi). In exchange, Grade 1 is the more ductile: elongation 30% versus 14% for Ti-6242, and Ti-6242 is harder (310 HB vs 120 HB). Ti-6242 is stiffer (114 GPa vs 103 GPa) and Ti-6242 runs hotter in service (540°C vs 300°C continuous). On the shop floor, Grade 1 machines more easily (fair vs poor) and Grade 1 welds better (excellent vs good).
Grade 1Choose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
Ti-6242Choose it when strength drives the design, or when the part sees heat.
Grade 1 vs Ti-6242: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Hardness, Rockwell C
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Same in both: Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Same in both: Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Same in both: Embodied Energy (primary production) 650 MJ/kg279,450 BTU/lb
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Grade 1 | Ti-6242 |
|---|---|---|
| Default condition | O | O |
| Relative cost | $$$$$ Specialty | $$$$$ Specialty |
| Min. machined wall | 1 mm | 1 mm |
| Best machined surface | Ra 1.6 µm | Ra 1.6 µm |
Both are offered for CNC machining and Sheet metal. Both take the same 20 finishes: AlCrN, AlTiN, Anodizing Type II, CVD Al2O3, CVD TiCN, CVD TiN, Cerakote, CrN, DLC, Electropolishing, HVOF Coating, MoS2 and 8 more.
Grade 1 vs Ti-6242 — frequently asked
Is Ti-6242 stronger than Grade 1?
Yes. Ti-6242 has a typical yield strength of 930 MPa (135 ksi) against 220 MPa (31.9 ksi) for Grade 1 — about 4.2 times as much. Tensile strength is 1,000 MPa (145 ksi) vs 300 MPa (43.5 ksi).
Which is cheaper, Grade 1 or Ti-6242?
Both sit in the same relative cost tier ($$$$$, specialty); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, Grade 1 or Ti-6242?
Grade 1. Its machinability rates fair (42/100) against poor (18/100) for Ti-6242; for welding the order is Grade 1 first (excellent, 90/100) then Ti-6242 (good, 60/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Grade 1 and Ti-6242 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.