Titanium C-1 vs ZTC4
Titanium · grade comparison
Titanium C-1 and ZTC4 are both titanium grades. ZTC4 is the stronger of the two: yield strength 840 MPa (122 ksi) against 210 MPa (30.5 ksi) for C-1, about 4.0 times as much; tensile strength follows at 910 MPa (132 ksi) vs 300 MPa (43.5 ksi). In exchange, C-1 is the more ductile: elongation 20% versus 8% for ZTC4, and ZTC4 is harder (325 HB vs 120 HB). ZTC4 is stiffer (110 GPa vs 103 GPa) and ZTC4 runs hotter in service (350°C vs 300°C continuous). On the shop floor, C-1 machines more easily (fair vs poor) and C-1 welds better (excellent vs very good).
C-1Choose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
ZTC4Choose it when strength drives the design, or when the part sees heat.
C-1 vs ZTC4: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Hardness, Rockwell C
Same in both: Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Castability
Same in both: Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | C-1 | ZTC4 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 1 finish: Plasma Spray.
C-1 vs ZTC4 — frequently asked
Is ZTC4 stronger than C-1?
Yes. ZTC4 has a typical yield strength of 840 MPa (122 ksi) against 210 MPa (30.5 ksi) for C-1 — about 4.0 times as much. Tensile strength is 910 MPa (132 ksi) vs 300 MPa (43.5 ksi).
Which is cheaper, C-1 or ZTC4?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, C-1 or ZTC4?
C-1. Its machinability rates fair (42/100) against poor (18/100) for ZTC4; for welding the order is C-1 first (excellent, 88/100) then ZTC4 (very good, 75/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in C-1 and ZTC4 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.