Titanium B817 Type I vs CP-Ti Powder (GB/T 30265)
Titanium · grade comparison
Titanium B817 Type I and CP-Ti Powder (GB/T 30265) are both titanium grades. Both yield at about 350 MPa — strength does not separate them. B817 Type I is the more ductile: elongation 18% versus 12% for CP-Ti Powder (GB/T 30265).
B817 Type IChoose it when the part is bent, formed or impact-loaded.
B817 Type I vs CP-Ti Powder (GB/T 30265): propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
B817 Type ICP-Ti Powder (GB/T 30265)
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Elongation at Break
Reduction in Area
Compressive Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell B
Same in both: Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34 · Tensile Strength (Ultimate) 450 MPa65.3 ksi · Yield Strength (0.2% offset) 350 MPa50.8 ksi · Shear Strength 300 MPa43.5 ksi · Hardness, Brinell 160 HB · Hardness, Vickers 170 HV
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 1,660°C3,020 °F · Liquidus Temperature 1,670°C3,038 °F
Thermal
How each material carries heat and how hot it can run.
Latent Heat of Fusion
Min Service Temperature
Same in both: Thermal Conductivity 16 W/m·K9.2 BTU/hr·ft·°F · Specific Heat Capacity 523 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Max Service Temperature (continuous) 300°C572 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3.1 % IACS · Electrical Resistivity 5.6×10⁻⁷ Ω·m22 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Same in both: Machinability 35 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Water
Typical Recycled Content
Same in both: Embodied Carbon (primary production) 48 kg CO₂/kg
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Same in both: Thermal Shock Resistance Index 8
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | B817 Type I | CP-Ti Powder (GB/T 30265) |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 1 finish: Plasma Spray.
B817 Type I vs CP-Ti Powder (GB/T 30265) — frequently asked
What is the difference between B817 Type I and CP-Ti Powder (GB/T 30265)?
Titanium B817 Type I and CP-Ti Powder (GB/T 30265) are both titanium grades. Both yield at about 350 MPa — strength does not separate them. B817 Type I is the more ductile: elongation 18% versus 12% for CP-Ti Powder (GB/T 30265).
Which is cheaper, B817 Type I or CP-Ti Powder (GB/T 30265)?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, B817 Type I or CP-Ti Powder (GB/T 30265)?
CP-Ti Powder (GB/T 30265). Its weldability rates very good (80/100) against very good (75/100) for B817 Type I.
Ready to make it?
Upload a CAD file and FabDigit prices the part in B817 Type I and CP-Ti Powder (GB/T 30265) side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.