Steel E80C-Ni1 vs ER70S-2
Steel · grade comparison
Steel E80C-Ni1 and ER70S-2 are both steel grades. E80C-Ni1 is the stronger of the two: yield strength 510 MPa (74 ksi) against 450 MPa (65.3 ksi) for ER70S-2, about 13% more; tensile strength follows at 600 MPa (87 ksi) vs 560 MPa (81.2 ksi). In exchange, ER70S-2 is the more ductile: elongation 28% versus 25% for E80C-Ni1, and E80C-Ni1 is harder (205 HB vs 155 HB). ER70S-2 conducts heat better (48 W/m·K vs 42 W/m·K). On the shop floor, ER70S-2 machines more easily (good vs fair) and ER70S-2 welds better (98 vs 88 out of 100).
E80C-Ni1Choose it when strength drives the design.
ER70S-2Choose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
E80C-Ni1 vs ER70S-2: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Compressive Strength
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Melting Point (Solidus)
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Min Service Temperature
Same in both: Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Max Service Temperature (continuous) 400°C752 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 25%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Modulus of Resilience
Thermal Diffusivity
Same in both: Specific Stiffness (E / density) 26.1 MN·m/kg · Thermal Shock Resistance Index 10
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | E80C-Ni1 | ER70S-2 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$ Standard | $$ Standard |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 9 finishes: Copper Plating, Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Manganese Phosphate, Plasma Spray, Silver Plating, Zinc Phosphate.
E80C-Ni1 vs ER70S-2 — frequently asked
Is E80C-Ni1 stronger than ER70S-2?
Yes. E80C-Ni1 has a typical yield strength of 510 MPa (74 ksi) against 450 MPa (65.3 ksi) for ER70S-2 — about 13% more. Tensile strength is 600 MPa (87 ksi) vs 560 MPa (81.2 ksi).
Which is cheaper, E80C-Ni1 or ER70S-2?
Both sit in the same relative cost tier ($$, standard); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, E80C-Ni1 or ER70S-2?
ER70S-2. Its machinability rates good (62/100) against fair (45/100) for E80C-Ni1; for welding the order is ER70S-2 first (excellent, 98/100) then E80C-Ni1 (excellent, 88/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in E80C-Ni1 and ER70S-2 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.