Beech vs Maple
Natural Material · grade comparison
Beech and Maple are both natural material grades. Beech is the stronger of the two: tensile strength 110 MPa (16 ksi) against 100 MPa (14.5 ksi) for Maple, about 10% more. In exchange, Maple is the more ductile: elongation 1.5% versus 1.2% for Beech. Beech is stiffer (14 GPa vs 12.6 GPa) and Beech runs hotter in service (100°C vs 90°C continuous). On the shop floor, Beech sits in a lower cost tier (budget, $) than Maple (standard, $$).
BeechChoose it when strength drives the design, or when the part sees heat.
MapleChoose it when the part is bent, formed or impact-loaded.
Beech vs Maple: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all natural material grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all natural material grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Flexural Strength
Shear Strength
Fracture Toughness (K_IC)
Physical
Density and transition temperatures.
Density
Porosity
Thermal
How each material carries heat and how hot it can run.
Specific Heat Capacity
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 0.16 W/m·K0.09 BTU/hr·ft·°F · Thermal Expansion (CTE, 20–100 °C) 4 µm/m·K2.2 µin/in·°F · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Dielectric Strength 4 kV/mm102 V/mil
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Water
Same in both: Embodied Carbon (primary production) 0.45 kg CO₂/kg · Typical Recycled Content 5%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Diffusivity 0.1 mm²/s · Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every natural material grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Beech | Maple |
|---|---|---|
| Default condition | — | — |
| Relative cost | $ Budget | $$ Standard |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Beech vs Maple — frequently asked
Is Beech stronger than Maple?
Yes. Beech has a typical tensile strength of 110 MPa (16 ksi) against 100 MPa (14.5 ksi) for Maple — about 10% more.
Which is cheaper, Beech or Maple?
Beech is the lower-cost material: it sits in the budget tier ($) while Maple is standard ($$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
When should I choose Beech over Maple?
Pick Beech when strength drives the design, or when the part sees heat. Pick Maple when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Beech and Maple side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.