PBO (Zylon) vs Technora
Composite · grade comparison
PBO (Zylon) and Technora are both composite grades. PBO (Zylon) is the stronger of the two: tensile strength 5,800 MPa (841 ksi) against 3,400 MPa (493 ksi) for Technora, about 71% more. In exchange, Technora is the more ductile: elongation 4.4% versus 3.5% for PBO (Zylon). Technora is lighter (1.39 g/cm³ vs 1.54 g/cm³ for PBO (Zylon)) and PBO (Zylon) is stiffer (180 GPa vs 72 GPa).
PBO (Zylon)Choose it when strength drives the design, or when the part sees heat.
TechnoraChoose it when the part is bent, formed or impact-loaded, or when weight is the constraint.
PBO (Zylon) vs Technora: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Poisson's Ratio
Shear Strength
Physical
Density and transition temperatures.
Density
Glass Transition (Tg)
Water Absorption (Saturation)
Same in both: Water Absorption (24 h) 2%
Thermal
How each material carries heat and how hot it can run.
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Limiting Oxygen Index
Max Service Temperature (short-term)
Thermal Conductivity
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Constant (1 MHz)
Same in both: Volume Resistivity 1×10¹⁴ Ω·cm
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 0%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | PBO (Zylon) | Technora |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
PBO (Zylon) vs Technora — frequently asked
Is PBO (Zylon) stronger than Technora?
Yes. PBO (Zylon) has a typical tensile strength of 5,800 MPa (841 ksi) against 3,400 MPa (493 ksi) for Technora — about 71% more.
Which is cheaper, PBO (Zylon) or Technora?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, PBO (Zylon) or Technora?
Technora, by a small margin. Both rate poor for machinability — 20/100 against 15/100 for PBO (Zylon).
Ready to make it?
Upload a CAD file and FabDigit prices the part in PBO (Zylon) and Technora side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.