Kevlar 49 vs Technora
Composite · grade comparison
Kevlar 49 and Technora are both composite grades. Technora is the stronger of the two: tensile strength 3,400 MPa (493 ksi) against 3,000 MPa (435 ksi) for Kevlar 49, about 13% more. Technora is the more ductile: elongation 4.4% versus 2.4% for Kevlar 49. Technora is lighter (1.39 g/cm³ vs 1.44 g/cm³ for Kevlar 49) and Kevlar 49 is stiffer (112 GPa vs 72 GPa).
TechnoraChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Kevlar 49 vs Technora: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Shear Strength
Physical
Density and transition temperatures.
Density
Glass Transition (Tg)
Water Absorption (Saturation)
Water Absorption (24 h)
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Limiting Oxygen Index
Max Service Temperature (short-term)
Same in both: Specific Heat Capacity 1,420 J/kg·K0.34 BTU/lb·°F
Electrical
Conductivity and insulation.
Electrical Resistivity
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Volume Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 0%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Diffusivity 0 mm²/s · Thermal Shock Resistance Index -1
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Kevlar 49 | Technora |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Kevlar 49 vs Technora — frequently asked
Is Technora stronger than Kevlar 49?
Yes. Technora has a typical tensile strength of 3,400 MPa (493 ksi) against 3,000 MPa (435 ksi) for Kevlar 49 — about 13% more.
Which is cheaper, Kevlar 49 or Technora?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which is easier to machine, Kevlar 49 or Technora?
Kevlar 49, by a small margin. Both rate poor for machinability — 25/100 against 20/100 for Technora.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Kevlar 49 and Technora side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.