Kevlar 149 vs Kevlar 29
Composite · grade comparison
Kevlar 149 and Kevlar 29 are both composite grades. Kevlar 149 is the stronger of the two: tensile strength 3,400 MPa (493 ksi) against 2,920 MPa (424 ksi) for Kevlar 29, about 16% more. In exchange, Kevlar 29 is the more ductile: elongation 3.6% versus 1.5% for Kevlar 149. Kevlar 149 is stiffer (175 GPa vs 70.5 GPa) and Kevlar 149 conducts heat better (0.05 W/m·K vs 0.04 W/m·K).
Kevlar 149Choose it when strength drives the design.
Kevlar 29Choose it when the part is bent, formed or impact-loaded.
Kevlar 149 vs Kevlar 29: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Tensile Strength (Ultimate)
Elongation at Break
Same in both: Poisson's Ratio 0.36 · Compressive Strength 400 MPa58 ksi
Physical
Density and transition temperatures.
Density
Water Absorption (24 h)
Water Absorption (Saturation)
Same in both: Glass Transition (Tg) 360°C680 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (short-term)
Same in both: Specific Heat Capacity 1,420 J/kg·K0.34 BTU/lb·°F · Max Service Temperature (continuous) 180°C356 °F · Min Service Temperature -196°C-321 °F · Limiting Oxygen Index 29%
Electrical
Conductivity and insulation.
Dissipation Factor (1 MHz)
Same in both: Electrical Resistivity 1×10¹³ Ω·m3.94×10²⁰ µΩ·in · Dielectric Constant (1 MHz) 4 · Volume Resistivity 1×10¹⁵ Ω·cm
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
UV / Weathering Resistance
Same in both: Corrosion Resistance 65 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Polishability
Same in both: Machinability 25 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 0%
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Thermal Shock Resistance Index
Same in both: Thermal Diffusivity 0 mm²/s
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Kevlar 149 | Kevlar 29 |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Kevlar 149 vs Kevlar 29 — frequently asked
Is Kevlar 149 stronger than Kevlar 29?
Yes. Kevlar 149 has a typical tensile strength of 3,400 MPa (493 ksi) against 2,920 MPa (424 ksi) for Kevlar 29 — about 16% more.
Which is cheaper, Kevlar 149 or Kevlar 29?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
When should I choose Kevlar 149 over Kevlar 29?
Pick Kevlar 149 when strength drives the design. Pick Kevlar 29 when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Kevlar 149 and Kevlar 29 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.