MnZn Ferrite vs TiO2 Ceramic
Ceramic · grade comparison
MnZn Ferrite and TiO2 Ceramic are both ceramic grades. TiO2 Ceramic is the stronger of the two: tensile strength 80 MPa (11.6 ksi) against 30 MPa (4.35 ksi) for MnZn Ferrite, about 167% more. TiO2 Ceramic is harder — 950 HV against 600 HV for MnZn Ferrite — which matters for wear surfaces and threads. TiO2 Ceramic is lighter (4.15 g/cm³ vs 4.85 g/cm³ for MnZn Ferrite) and TiO2 Ceramic is stiffer (250 GPa vs 150 GPa). On the shop floor, MnZn Ferrite machines more easily (poor vs not recommended) and MnZn Ferrite sits in a lower cost tier (premium, $$$) than TiO2 Ceramic (high, $$$$).
MnZn FerriteChoose it when the part is machined in volume, or when cost is the deciding factor.
TiO2 CeramicChoose it when strength drives the design, or when surface hardness matters.
MnZn Ferrite vs TiO2 Ceramic: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all ceramic grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all ceramic grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Flexural Strength
Fracture Toughness (K_IC)
Hardness, Vickers
Hardness, Knoop
Hardness, Mohs
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Porosity
Refractive Index
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Resistivity
Volume Resistivity
Dielectric Strength
Dielectric Constant (1 MHz)
Dissipation Factor (1 MHz)
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sintering / Firing Temperature
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Thermal Diffusivity
Same in both: Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every ceramic grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | MnZn Ferrite | TiO2 Ceramic |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$ Premium | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
MnZn Ferrite vs TiO2 Ceramic — frequently asked
Is TiO2 Ceramic stronger than MnZn Ferrite?
Yes. TiO2 Ceramic has a typical tensile strength of 80 MPa (11.6 ksi) against 30 MPa (4.35 ksi) for MnZn Ferrite — about 167% more.
Which is cheaper, MnZn Ferrite or TiO2 Ceramic?
MnZn Ferrite is the lower-cost material: it sits in the premium tier ($$$) while TiO2 Ceramic is high ($$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, MnZn Ferrite or TiO2 Ceramic?
MnZn Ferrite. Its machinability rates poor (15/100) against not recommended (5/100) for TiO2 Ceramic.
Ready to make it?
Upload a CAD file and FabDigit prices the part in MnZn Ferrite and TiO2 Ceramic side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.