Aluminum EN AW-5083 Cast Plate vs Hokotol
Aluminum · grade comparison
Aluminum EN AW-5083 Cast Plate and Hokotol are both aluminum grades, both mold quality al. Hokotol is the stronger of the two: yield strength 480 MPa (69.6 ksi) against 125 MPa (18.1 ksi) for EN AW-5083 Cast Plate, about 3.8 times as much; tensile strength follows at 540 MPa (78.3 ksi) vs 270 MPa (39.2 ksi). In exchange, EN AW-5083 Cast Plate is the more ductile: elongation 12% versus 6% for Hokotol, and Hokotol is harder (165 HB vs 70 HB). EN AW-5083 Cast Plate is lighter (2.66 g/cm³ vs 2.82 g/cm³ for Hokotol) and Hokotol runs hotter in service (120°C vs 65°C continuous). On the shop floor, Hokotol machines more easily (very good vs good), EN AW-5083 Cast Plate welds better (excellent vs poor), and EN AW-5083 Cast Plate sits in a lower cost tier (standard, $$) than Hokotol (premium, $$$).
EN AW-5083 Cast PlateChoose it when the part is bent, formed or impact-loaded, or when weight is the constraint.
HokotolChoose it when strength drives the design, or when the part sees heat.
EN AW-5083 Cast Plate vs Hokotol: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Same in both: Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Castability
Brazeability / Solderability
Polishability
Machinability Rating (AISI 1212 = 100 %)
Sustainability
Primary-production footprint per kilogram.
Embodied Carbon (primary production)
Typical Recycled Content
Same in both: Embodied Energy (primary production) 155 MJ/kg66,638 BTU/lb · Embodied Water 1,200 L/kg144 gal/lb
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | EN AW-5083 Cast Plate | Hokotol |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$ Standard | $$$ Premium |
| Min. machined wall | 1 mm | 0.5 mm |
| Best machined surface | Ra 1.6 µm | Ra 0.8 µm |
Both are offered for CNC machining. Both take the same 16 finishes: Anodizing Type II, Cerakote, Chem Film (Alodine), DLC, E-Coating, Electroless Nickel (EN), Electropolishing, Epoxy Coating, Gold Plating, Hard Anodize Type III w/ PTFE, Hard Anodizing Type III, Nickel Plating and 4 more.
EN AW-5083 Cast Plate vs Hokotol — frequently asked
Is Hokotol stronger than EN AW-5083 Cast Plate?
Yes. Hokotol has a typical yield strength of 480 MPa (69.6 ksi) against 125 MPa (18.1 ksi) for EN AW-5083 Cast Plate — about 3.8 times as much. Tensile strength is 540 MPa (78.3 ksi) vs 270 MPa (39.2 ksi).
Which is cheaper, EN AW-5083 Cast Plate or Hokotol?
EN AW-5083 Cast Plate is the lower-cost material: it sits in the standard tier ($$) while Hokotol is premium ($$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, EN AW-5083 Cast Plate or Hokotol?
Hokotol. Its machinability rates very good (82/100) against good (62/100) for EN AW-5083 Cast Plate; for welding the order is EN AW-5083 Cast Plate first (excellent, 90/100) then Hokotol (poor, 18/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in EN AW-5083 Cast Plate and Hokotol side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.