Aluminum EN AC-43200-T5 vs EN AC-43200-T6
Aluminum · EN AC-43200 temper comparison
EN AC-43200-T5 and EN AC-43200-T6 are two conditions of the same aluminum grade, EN AC-43200: T5 (cooled from hot working and artificially aged) versus T6 (solution heat treated and artificially aged). The chemistry is identical, so every difference below comes from the condition. EN AC-43200-T6 is the stronger of the two: yield strength 220 MPa (31.9 ksi) against 130 MPa (18.9 ksi) for EN AC-43200-T5, about 69% more; tensile strength follows at 260 MPa (37.7 ksi) vs 200 MPa (29 ksi). EN AC-43200-T6 is harder — 90 HB against 70 HB for EN AC-43200-T5 — which matters for wear surfaces and threads. On the shop floor, EN AC-43200-T6 welds better (good vs fair).
EN AC-43200-T6Choose it when strength drives the design, or when surface hardness matters.
EN AC-43200-T5 vs EN AC-43200-T6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 73 GPa10.6 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33 · Elongation at Break 1.5% · Charpy V-Notch Impact (RT) 3 J2.2 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 2.65 g/cm³0.1 lb/in³ · Melting Point (Solidus) 555°C1,031 °F · Liquidus Temperature 595°C1,103 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 21 µm/m·K11.7 µin/in·°F · Latent Heat of Fusion 425 J/g183 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Same in both: Castability 90 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Same in both: Embodied Water 1,100 L/kg132 gal/lb · Typical Recycled Content 70%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
EN AC-43200-T5 vs EN AC-43200-T6 — frequently asked
Is EN AC-43200-T6 stronger than EN AC-43200-T5?
Yes. EN AC-43200-T6 has a typical yield strength of 220 MPa (31.9 ksi) against 130 MPa (18.9 ksi) for EN AC-43200-T5 — about 69% more. Tensile strength is 260 MPa (37.7 ksi) vs 200 MPa (29 ksi).
Which condition does FabDigit quote by default, T5 or T6?
F is the default EN AC-43200 condition in the FabDigit quote flow (neither T5 nor T6). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, EN AC-43200-T5 or EN AC-43200-T6?
EN AC-43200-T6. Its weldability rates good (55/100) against fair (42/100) for EN AC-43200-T5.
Ready to make it?
Upload a CAD file and FabDigit prices the part in EN AC-43200-T5 and EN AC-43200-T6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.