Aluminum 295.0-F vs 295.0-T62
Aluminum · 295.0 temper comparison
295.0-F and 295.0-T62 are two conditions of the same aluminum grade, 295.0: F (as fabricated) versus T62 (T6, heat treated by the user). The chemistry is identical, so every difference below comes from the condition. 295.0-T62 is the stronger of the two: yield strength 220 MPa (31.9 ksi) against 85 MPa (12.3 ksi) for 295.0-F, about 159% more; tensile strength follows at 285 MPa (41.3 ksi) vs 145 MPa (21 ksi). In exchange, 295.0-F is the more ductile: elongation 3% versus 2% for 295.0-T62, and 295.0-T62 is harder (90 HB vs 55 HB). 295.0-T62 runs hotter in service (150°C vs 100°C continuous) and 295.0-T62 conducts heat better (151 W/m·K vs 135 W/m·K). On the shop floor, 295.0-T62 machines more easily (very good vs good).
295.0-FChoose it when the part is bent, formed or impact-loaded.
295.0-T62Choose it when strength drives the design, or when the part sees heat.
295.0-F vs 295.0-T62: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 70 GPa10.2 Msi · Shear Modulus 26 GPa3.8 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33 · Fracture Toughness (K_IC) 17 MPa·√m15.5 ksi·√in
Physical
Density and transition temperatures.
Same in both: Density 2.81 g/cm³0.1 lb/in³ · Melting Point (Solidus) 521°C970 °F · Liquidus Temperature 645°C1,193 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 963 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23 µm/m·K12.8 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.75 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 25 / 100 · Formability (cold) 10 / 100 · Castability 50 / 100 · Brazeability / Solderability 20 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
295.0-F vs 295.0-T62 — frequently asked
Is 295.0-T62 stronger than 295.0-F?
Yes. 295.0-T62 has a typical yield strength of 220 MPa (31.9 ksi) against 85 MPa (12.3 ksi) for 295.0-F — about 159% more. Tensile strength is 285 MPa (41.3 ksi) vs 145 MPa (21 ksi).
Which condition does FabDigit quote by default, F or T62?
T6 is the default 295.0 condition in the FabDigit quote flow (neither F nor T62). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 295.0-F or 295.0-T62?
295.0-T62. Its machinability rates very good (75/100) against good (62/100) for 295.0-F.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 295.0-F and 295.0-T62 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.