Titanium Ti-17 vs Ti-6Al-6V-2Sn
Titanium · grade comparison
Titanium Ti-17 and Ti-6Al-6V-2Sn are both titanium grades. Ti-17 is the stronger of the two: yield strength 1,075 MPa (156 ksi) against 980 MPa (142 ksi) for Ti-6Al-6V-2Sn, about 10% more; tensile strength follows at 1,150 MPa (167 ksi) vs 1,050 MPa (152 ksi). In exchange, Ti-6Al-6V-2Sn is the more ductile: elongation 14% versus 10% for Ti-17. Ti-17 runs hotter in service (350°C vs 315°C continuous).
Ti-17Choose it when strength drives the design, or when the part sees heat.
Ti-6Al-6V-2SnChoose it when the part is bent, formed or impact-loaded.
Ti-17 vs Ti-6Al-6V-2Sn: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Hardness, Vickers
Hardness, Brinell
Same in both: Shear Modulus 42.5 GPa6.2 Msi · Poisson's Ratio 0.32
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Electrical
Conductivity and insulation.
Electrical Resistivity
Electrical Conductivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Castability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Ti-17 | Ti-6Al-6V-2Sn |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$$$ High |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Both take the same 1 finish: Plasma Spray.
Ti-17 vs Ti-6Al-6V-2Sn — frequently asked
Is Ti-17 stronger than Ti-6Al-6V-2Sn?
Yes. Ti-17 has a typical yield strength of 1,075 MPa (156 ksi) against 980 MPa (142 ksi) for Ti-6Al-6V-2Sn — about 10% more. Tensile strength is 1,150 MPa (167 ksi) vs 1,050 MPa (152 ksi).
Which is cheaper, Ti-17 or Ti-6Al-6V-2Sn?
Both sit in the same relative cost tier ($$$$, high); the part price will be decided by machining time, tolerance and quantity rather than by the material.
Which welds better, Ti-17 or Ti-6Al-6V-2Sn?
Ti-6Al-6V-2Sn. Its weldability rates fair (35/100) against poor (30/100) for Ti-17.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Ti-17 and Ti-6Al-6V-2Sn side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.