Titanium Grade 5-HIP vs Grade 5-STA
Titanium · Grade 5 temper comparison
Grade 5-HIP and Grade 5-STA are two conditions of the same titanium grade, Grade 5: HIP (hot isostatic pressed) versus STA (solution treated and aged). The chemistry is identical, so every difference below comes from the condition. Grade 5-STA is the stronger of the two: yield strength 1,070 MPa (155 ksi) against 890 MPa (129 ksi) for Grade 5-HIP, about 20% more; tensile strength follows at 1,150 MPa (167 ksi) vs 970 MPa (141 ksi). In exchange, Grade 5-HIP is the more ductile: elongation 16% versus 10% for Grade 5-STA, and Grade 5-STA is harder (380 HB vs 319 HB). Grade 5-HIP runs hotter in service (400°C vs 350°C continuous).
Grade 5-HIPChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Grade 5-STAChoose it when strength drives the design.
Grade 5-HIP vs Grade 5-STA: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 113.8 GPa16.5 Msi · Shear Modulus 44 GPa6.4 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 4.43 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,604°C2,919 °F · Liquidus Temperature 1,660°C3,020 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 526 J/kg·K0.13 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 365 J/g157 BTU/lb · Min Service Temperature -253°C-423 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1 % IACS · Electrical Resistivity 1.78×10⁻⁶ Ω·m70.1 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 75 / 100 · Formability (cold) 25 / 100 · Castability 45 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 650 MJ/kg279,450 BTU/lb · Embodied Carbon (primary production) 42 kg CO₂/kg · Embodied Water 900 L/kg108 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Grade 5-HIP vs Grade 5-STA — frequently asked
Is Grade 5-STA stronger than Grade 5-HIP?
Yes. Grade 5-STA has a typical yield strength of 1,070 MPa (155 ksi) against 890 MPa (129 ksi) for Grade 5-HIP — about 20% more. Tensile strength is 1,150 MPa (167 ksi) vs 970 MPa (141 ksi).
Which condition does FabDigit quote by default, HIP or STA?
O is the default Grade 5 condition in the FabDigit quote flow (neither HIP nor STA). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Grade 5-HIP or Grade 5-STA?
Grade 5-HIP, by a small margin. Both rate poor for machinability — 22/100 against 17/100 for Grade 5-STA.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Grade 5-HIP and Grade 5-STA side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.