Steel G34CrMo4 +N vs G34CrMo4 +QT1
Steel · G34CrMo4 temper comparison
G34CrMo4 +N and G34CrMo4 +QT1 are two conditions of the same steel grade, G34CrMo4: +N (normalized) versus +QT1 (quenched and tempered, lower strength class). The chemistry is identical, so every difference below comes from the condition. G34CrMo4 +QT1 is the stronger of the two: yield strength 570 MPa (82.7 ksi) against 460 MPa (66.7 ksi) for G34CrMo4 +N, about 24% more; tensile strength follows at 760 MPa (110 ksi) vs 700 MPa (102 ksi). G34CrMo4 +QT1 is harder — 235 HB against 210 HB for G34CrMo4 +N — which matters for wear surfaces and threads.
G34CrMo4 +QT1Choose it when strength drives the design, or when surface hardness matters.
G34CrMo4 +N vs G34CrMo4 +QT1: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 580 MPa84.1 ksi · Shear Strength 460 MPa66.7 ksi
Physical
Density and transition temperatures.
Same in both: Density 7.83 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 40 / 100 · Formability (cold) 10 / 100 · Castability 65 / 100 · Brazeability / Solderability 45 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 75%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
G34CrMo4 +N vs G34CrMo4 +QT1 — frequently asked
Is G34CrMo4 +QT1 stronger than G34CrMo4 +N?
Yes. G34CrMo4 +QT1 has a typical yield strength of 570 MPa (82.7 ksi) against 460 MPa (66.7 ksi) for G34CrMo4 +N — about 24% more. Tensile strength is 760 MPa (110 ksi) vs 700 MPa (102 ksi).
Which condition does FabDigit quote by default, +N or +QT1?
+QT1 is the default G34CrMo4 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, G34CrMo4 +N or G34CrMo4 +QT1?
G34CrMo4 +N. Its machinability rates good (56/100) against fair (50/100) for G34CrMo4 +QT1.
Ready to make it?
Upload a CAD file and FabDigit prices the part in G34CrMo4 +N and G34CrMo4 +QT1 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.